Waterproofing Excavations Around the Benjamin Waller House, Williamsburg, Virginia

Lily Richards

2001

Colonial Williamsburg Foundation Library Research Report Series - 1682 John D. Rockefeller, Jr. Library
Colonial Williamsburg Foundation

Williamsburg, Virginia

2002

Waterproofing Excavations Around
the Benjamin Waller House,
Williamsburg, Virginia

by
Lily Richards


The Colonial Williamsburg Foundation Department of Archaeological Research
P.O. Box 1776

Williamsburg, VA 23187-1776
(757) 220-7330
Lily Richards
Project Archaeologist
Marley R. Brown III
Principal Investigator

February 2001

i

Management Summary

From March 1 through May 15, 2000, the Colonial Williamsburg Foundation's Department of Archaeological Research (D.A.R.) conducted archaeological investigations at the Benjamin Waller House, located at the intersection of Francis and Waller Streets on Block 1 in Williamsburg's Historic Area. Excavations were conducted in advance of waterproofing activities which were to take place from June through September 2000. In the course of these activities, large portions of the archaeological record contained in the two meters surrounding the house was to be destroyed. The excavations were an attempt to uncover, interpret, and record the archaeological and cultural remains prior to the waterproofing.

Excavation consisted of digging trenches two meters wide around most of the Waller House (Figure 1). A total of seven trenches were excavated, following the natural stratigraphy, to the level of undisturbed subsoil. Intact features in the layers and in subsoil were carefully excavated and recorded. All soil removed from the trenches and features was screened for artifacts using ¼-inch steel mesh.

During the course of excavations, several eighteenth- and nineteenth-century layers and features were uncovered. Layers contained a moderate concentration of domestic artifacts associated with the continual occupation of the house from the eighteenth through the twentieth centuries. Features included a Waller-era brick vaulted drain, an eighteenth- RR168201 Figure 1. Location of excavation trenches. ii century refuse midden, several eighteenth-century planting features, a nineteenth-century brick foundation, and a number of scaffolding holes related to the construction of the eighteenth-century "L" (or "ell") wing.

The spring 2000 excavations helped to trace the occupation and domestic use of the Waller House during the eighteenth and nineteenth centuries, with the Waller era as the focus of the investigation. While no definitive date could be attached to the house due to destruction of the builder's trench during the 1950s, excavations provided a better understanding of the landscape around the house during Waller's occupation and specifically answered several questions involving the use of the eighteenth-century vaulted or brick arch drain.

iii

Acknowledgments

The successful completion of this project was due to the hard work of a talented group of people. Marley R. Brown III, Director of the Department of Archaeological Research, oversaw the project and provided support throughout. Staff archaeologist David Muraca offered his guidance both in and out of the field. Staff archaeologist Greg Brown lent his expert editing skills. Mark Wenger and Willie Graham of Architectural Research and Tom Taylor of Architectural Conservation provided architectural interpretations along with a better understanding of the work done during the 1950s renovations. Kevin Kelly of Historical Research shared many helpful ideas during the course of the project. Artifacts were analyzed and inventoried by Isabel Jenkins. Heather Harvey created the graphics for the report. This project would not have possible without the hard work of a dedicated field crew, consisting of David Brown, Jameson Harwood, Isabel Jenkins, Hank Lutton, Kiera McReynolds, Katherine Schupp, and Katy Thomason. Finally, many thanks should be given to Mr. and Mrs. F.G. Summit for their endless patience, support, and enthusiasm throughout the course of the excavations, and for the many delicacies they shared.

iv

Table of Contents

Page
Management Summaryi
Acknowledgmentsiii
List of Figuresv
Chapter 1. Background1
Historical Overview1
The Waller Property1
The Life of Benjamin Waller2
Previous Archaeology4
Chapter 2. Archaeology5
Research Design/Methods5
Results6
The Benjamin Waller Period6
Planting Features (Master Context M5)6
Layer (Master Context M6)11
Shell Midden 01BB-109 and Related Layers12
Planting Features 01BB-146, 01BB-155, 01BB-15814
Layer (Master Context M7)16
Scaffolding Features 01BB-168 and 01BB-17516
Layer (Master Context M10)17
The Brick Arch Drain18
1950s Excavations19
Drain Form20
Drain Function20
Post-Benjamin Waller Era Functions22
Nineteenth-Century Foundation 01BB-15222
Layer (Master Context M9)23
Victorian Porch (Master Context M11)24
Chapter 3. Conclusions25
Bibliography26
Appendix A. Master Context List27
Appendix B. Artifact Inventory28
v
Page
Figure 1. Location of excavation trenchesi
Figure 2. 1749 Waller map1
Figure 3. Planting features (Master Context M5)7
Figure 4. Profile of planting feature 01BB-128
Figure 5. Profile of planting feature 01BB-249
Figure 6. Profile of planting feature 01BB-9010
Figure 7. Profile of planting feature 01BB-5710
Figure 8. Plan view of layer M611
Figure 9. Map of Waller garden12
Figure 10. Plan of shell midden 01BB-10913
Figure 11. Plan of planting feature 01BB-14615
Figure 12. Profile of planting feature 01BB-15515
Figure 13. Plan view of layer M716
Figure 14. Plan view of features 01BB-168 and 01BB-17517
Figure 15. Plan view of layer M1018
Figure 16. Plan of vaulted brick drain19
Figure 17. Profile of vaulted brick drain19
Figure 18. Frenchman's map22
Figure 19. Plan view of foundation 01BB-15223
Figure 20. Profile of foundation 01BB-15223
1

Chapter 1.
Background

Historical Overview

The Waller Property

The first reference to Benjamin Waller's ownership of the property on which the Waller House now stands is a 1749 map drawn by his brother William in which the lot is marked "Mr. Benjamin Waller's Lot" (Figure 2). While it is clear that Benjamin Waller owned the property on Block 1 as early as 1749, and certainly by 1756 when an act from Hening's Statutes referred to the property as that of Benjamin Waller, no historical evidence exists which establishes a date for the construction of the house. However, the same act which established ownership of the Waller property also included the phrase "as soon as the same shall be built upon," implying that Benjamin Waller had not yet built on the property.

The first actual reference to the existence of a house on the Waller lot came in 1768, when an announcement of sale referred to a dwelling house "very near Mr. Waller's" (Stephenson 1950: 5). In March 1771 an ad in the Virginia Gazette states that the house of Colonel Johnson is behind "that of Mr. Waller." So while it seems likely that Benjamin Waller would have built a home prior to 1768, it is not until then that one can say with any certainty that a house existed on the Waller property. It seems odd, however, that the lot would have sat empty for nearly ten years considering the fact that lots within the city of Williamsburg reverted back to the city if the owner failed to build within two years of acquiring property. The 1782 Frenchman's Map shows the house in its completed form as an "L"-shaped building.

Benjamin Waller's house and property passed to his son Robert Hall Waller upon Benjamin's death in May 1786 and remained in Robert's possession until his death in March 1808. Robert's widow, Martha C. Waller, lived in the house until her death in April 1816. At this time Robert and Martha's son-in-law, George Blow, advertised the property for sale. However, Robert Waller's nephew Colonel Burwell Bassett petitioned to rent the property, charging Blow with asking too much for sale of the property and appealing to a desire to keep the property in the hands of the Waller family. Blow agreed to Bassett's petition, and a Mrs. Euphelia Claiborne lived in the house with Bassett's permission from 1817 until 1820.

At this point the historical record becomes rather confusing. It appears that in 1822 George Blow sold the property to William H. Waller, son of Robert H. Waller and grandson of Benjamin Waller. William held the property until his death in 1834, when it became part of his estate holdings. Whether or not anyone was living in the house during this time is unclear. In 1853, according to Williamsburg land tax records, Williams's nephew Robert P. Waller took over ownership of the property. In 1869 Robert died and left the property to his daughter Mary C. Mercer, who held the property until 1885. At this point 2 RR168202 Figure 2. 1749 Waller map (Waller property shown by arrow). the property on Francis Street passed out of the hands of the Waller family after having been in their possession for nearly 140 years.

In 1885 the house was sold at public auction to M.R. Harrell. The property was then split for the first time with the southeast portion of the lot going to R.J Barlow and the dwelling house and surrounding property to Virginia Morecock. The Morecock family 3 held the property until it was sold to Colonial Williamsburg Incorporated on December 17, 1940 (Stephenson 1950).

The Life of Benjamin Waller

Benjamin Waller was born to Colonel John Waller and Dorothy Kind at the family seat of Endfield in King and Queen County in 1716. At age ten John Carter, son of Robert "King" Carter and Secretary of State, took Waller to Williamsburg so that he might attend grammar school at the College of William & Mary. From there he attended law school, also at William & Mary, and upon finishing his degree became a law clerk at the Secretary's office (Greenman 1994).

This was just the beginning of what was to be a highly distinguished career. By 1737 Waller had been appointed Deputy Clerk of James City County. That same year Governor Gooch appointed Waller Registrar of the Court of Vice Admiralty, and this before he even passed the bar exam. In 1738 Waller was given permission from the government to practice as an attorney, and in 1739 he became full Clerk of James City County. He was appointed King's Attorney of Gloucester, York, and James City Counties in 1739 as well. In 1740, Waller became clerk assistant of the House of Burgesses and in 1742 was appointed clerk of the two most powerful committees in the House, Propositions and Grievances and Privileges, a position to which his father had proceeded him (Heaton 1967).

In 1744 Waller was elected to the House of Burgesses. At this point he was considered one of Williamsburg's more prominent citizens, although he would never attain the status of a Peyton Randolph or John Carter. Unlike these men, he did not acquire his seat by "right" but rather through laboring to gain the respect of his influential friends (Greenman 1994).

By the 1740s, Waller had begun to sell off the land which he had accumulated around the eastern end of town. Throughout the mid-century he continued to improve upon his lots and sell them to other Williamsburg businessmen. It was perhaps because of his interest in selling off his lands at a profit that he was one of the major supporters of retaining Williamsburg as Virginia's capital after the Capitol building burned in January 1747. Waller was influential in maintaining Williamsburg as the capital and was one of the eight persons appointed to oversee the rebuilding of the Capitol (Greenman 1994).

1747 proved to be a busy year for Waller, for in January, at the same time he was dealing with the destruction of the Capitol building, he married Martha Hall, thought to be the cousin of attorney Stephen Dewey. At this point Waller had most likely built at least the first part of his house on Francis Street, though no conclusive documentary evidence exists to support this. Though the construction date for the house is uncertain, it seems likely that he would have built the house in time to move his new bride into a respectable home.

Waller's prominence in Williamsburg continued after his marriage. In 1754 he was appointed to oversee the building of a bridge across Queen's Creek. In 1755 he directed workmen in erecting the brick wall around Bruton Parish Church, and in 1769 he became a sitting vestryman at the same. In June 1770, Waller was named, by act of assembly, to the court of directors of the Public Hospital.

4

By participating in politics and local society, Benjamin Waller was following a family legacy. Along the way he befriended men like Governor Gooch and Secretary Carter who rewarded him for his friendship and diligence. He became the executor of middling estates and a seller of convenient lots, thereby cultivating a group of upwardly mobile artisans and tavern keepers as his friends and supporters. He also socialized with scholars like George Wythe, all of which made him the "quintessential middle man" (Greenman 1994).

As tensions between the American colonies and Great Britain increased, so did Waller's discomfort. Neither a strict loyalist nor a revolutionary, Waller found his position increasingly awkward. In 1761 he declined reelection to the House of Burgesses because "he did not think it right to oppose the measures of the [British] administration and couldn't reconcile to himself to oppose those proposed by his countrymen" (Heaton 1967).

Despite this, Waller, throughout his life, remained a model upper middle gentry man. He had ten children who survived to adulthood, all of whom married well to persons of middle and upper gentry status. Throughout his practice as a lawyer, the positions of those whose estates he was asked to execute steadily increased. He continued to be a man to whom his community turned to in times of need, and garnered the respect of the gentry class, the up and coming businessmen, and the great minds of the time.

Previous Archaeology

In 1950, renovations of the Benjamin Waller House were begun in earnest. Prior to this, James Knight, the architectural draftsperson in charge of Colonial Williamsburg's archaeology program, excavated most of the area surrounding the house. He uncovered a wealth of archaeological features and artifacts, but left behind a complex series of unexplored areas for current archaeologists to uncover.

Two important archaeological discoveries were made in the 1950s. The first of these was a brick arch drain which exited the Waller House basement on its northeast corner and extended northeast past the Waller Office (see below). The full extent of the drain was never completely revealed, and more questions as to its use were raised than were answered. It was obviously one of the largest brick drains to be uncovered in the Historic Area, a fact which complicated what otherwise would have simply been considered a drainage route for a flooded basement. At the time, Knight's only other explanation for the size of the drain was that it provided an escape route from the Waller basement, an idea that has more recently been discounted by other scholars. The form and function of the Waller drain will be discussed in detail later in this report.

A second major feature uncovered during Knight's excavations around the Waller foundation was the base of the lightning rod, determined to be an original. Though part of it has been replaced, the lightening rod remains attached to the western wall of the house today.

Jimmy Knight and his crew also uncovered the original foundations of several of the Waller outbuildings during their excavations. Among those located were the Waller dairy, kitchen, office, smoke house, stable, and storehouse. Each of these buildings has since been reconstructed on the foundations uncovered by Knight in 1950.

5

Chapter 2.
Archaeology

Research Design/Methods

Archaeologists from Colonial Williamsburg's Department of Archaeological Research excavated seven trenches along the foundation of the Benjamin Waller House during the spring 2000 excavations (see Figure 1). Because of the "L"- shape of the building, there was a large area to be investigated. Everything within two meters of the house would be subject to disturbance during waterproofing activities and therefore had to be carefully examined to ensure that all relevant archaeological data was interpreted prior to its destruction. Two trenches were excavated along the north wall of the main cell of the house. The northeast trench measured 12 x2 m and the northwest trench measured 10 x 2 m. A 6 x 2 m trench was placed along the west wall of the main cell of the house. Along the south wall of the main cell of the house, archaeologists excavated a 10 x 2 m trench. Trenches were also excavated around the base of the ell wing, including an 8 x 2 m trench along the west wall, a 2.6 x 2 m trench along the south wall, and a 2 x 2 m trench along the east wall. Although each trench was excavated separately, the data from each was considered in relationship to the entire area.

Though parts of the area had been excavated by James Knight in the 1950s, large sections had been left unexcavated, largely to avoid boxwood trees which grew in great numbers around the house. Before any analysis of intact cultural layers and features could be undertaken, archaeologists had to first remove the soil which Knight had used to fill in his excavation units. This was a complex task requiring careful delineation between modern and historic contexts. The degree of previous excavation to which the area had already been subject varied from trench to trench, but once the fill had been removed, archaeologists discovered that a great deal of information had been left virtually untouched by Knight's crew. It was to these remaining cultural evidence that archaeologists turned their attention for the majority of the excavation.

Excavations were carried out using shovels and hand trowels. Archaeologists followed the natural stratigraphy, recognizing layer changes by changes in soil texture and color. All soil was sifted through ¼-inch steel mesh screen and all artifacts were saved in polyethylene bags. All features were recorded on detailed plan maps. Each layer and feature was assigned its own context number. A context record was filled out for each context using an on-site handheld computer. All relevant information regarding artifacts, soil layers, and cultural remains was included in each record. At the end of each day, information from the handheld was downloaded into the collections management database Re:Discovery.

Later, related contexts were combined to form "master contexts," representing larger stratigraphic units (structures, fence lines, etc.). These master contexts are generally prefaced with an "M" (for example, master context "M11").

6

Artifacts recovered were sent to the D.A.R. Lab for processing, identification, and analysis. Artifacts were washed, identified, inventoried, and labeled by context. Each context was assigned a terminus post quem (TPQ) date when possible. The TPQ date establishes the earliest date at which a layer or feature could have been deposited, based on the artifact with the most recent date of manufacture. Artifacts were inventoried by ware type, with all important functional and morphological characteristics noted. All documentation and artifacts from the excavations are stored at the D.A.R. lab.

Results

The Benjamin Waller Period

Once all landscaping-related soils and previous archaeology fill had been removed from around the house, a number of features related to Benjamin Waller's occupation of the house were revealed. Unfortunately, during the 1950s waterproofing of the Waller foundation, the builder's trench was destroyed. During the process of building a house with a basement, a large hole is dug. The house is then built inside this hole. The remaining space which is filled in with dirt, and into which contemporary artifacts often fall, is referred to as the "builder's trench." No records of any archaeological investigation of the Waller House trench exists today. This is particularly unfortunate due to the fact that no definitive date has been established for the construction of the house. Historical records indicate that Waller owned the property by 1749 and that the house was definitely standing in 1775 when Lord Dunmore was a visitor there (Stephenson 1950), but it is unclear when exactly during that period the house was built. Artifacts from the builder's trench could possibly have provided archaeologists with a more precise date. However, if the builder's trench was indeed archaeologically excavated, no records remain.

Several important features did survive the 1950s house renovations. Though most were cut, often multiple times, by modern intrusions, in most cases enough information remained to allow archaeologists to formulate opinions as to their nature. Though the 1950s excavation was largely responsible for the loss of information, landscaping, both modern and historic, did its share of damage to the archaeological record surrounding the Waller House as well. Below is an analysis of the layers and features uncovered during the 2000 excavations and attributable to Waller's occupation of the house.

Planting Features (Master Context M5)

Understanding what colonial Virginians found aesthetically pleasing and how they organized their public space is a question many archaeologists find intriguing. However, garden or planting features can be one of the more illusive archaeological features. At the Benjamin Waller house, archaeologists uncovered evidence early on in their excavations which provided a clue as to how the Waller family landscaped the part of their yard which would be available for public viewing. An in-depth study had long since been conducted into the exact arrangement of the Waller gardens, a veritable showplace in the rear of the house, which have been painstakingly reconstructed based on a sketch made of the gardens by the granddaughter of Benjamin Waller (Stephenson 1950). Little was known, however, about the area between the Waller House and Francis Street.

7

Modern boxwood trees grew along the north or front wall of the house just prior to archaeological excavations. They left behind a large archaeological footprint, nearly obliterating the remains of the Waller plantings. However, six systematically placed planting holes dating to the Waller era were visible beneath these modern boxwood holes. In some cases, whole sections of the Waller planting features had survived, partially cut away by Jimmy Knight excavation trenches and the modern boxwoods.

The actual dimensions of the holes were difficult to determine as they had in most cases been largely cut away by modern intrusions and the north wall of the excavation trench. However, the holes were similar in depth, fill, and profile shape. That, combined with the fact that the features were evenly spaced at approximately two meter (6.6 foot) intervals, suggested that the features were related (Figure 3). The features' proximity to the house, combined with the size and irregular profiles of the features, indicated that the features actually represented planting holes.

Planting feature 01BB-12 was the first of these features to be excavated. Located approximately 50 cm east of the front porch (all measurements concerning M5 are approximate, since in most cases only portions of the original features remained), it was cut both by Jimmy Knight trench 01BB-7 and modern planting hole 01BB-22 (see Figure 3), so that only 95 x 65 cm remained to be excavated. In addition, the north half of the feature was located outside the excavation area. The feature appeared to have been vaguely circular in shape. It contained a friable sandy clay loam fill. While in plan feature 12 seemed relatively straightforward, exploration revealed that the profile was irregular (Figure 4). It was this irregular profile and the lack of a postmold which suggested that it was a planting hole rather than a posthole. A large root stain appeared at the bottom of the excavated hole, probably representing a primary root from the original plant. The hole ranged in depth from 10 to 42 cm and was slightly stepped on the southern half. Artifacts recovered included tobacco pipes, wine bottle and window glass, porcelain, and Jackfield-type earthenware, which provided a TPQ of 1740, among others. The early TPQ date for the feature, along with those of the related planting holes, indicates that the plantings were related to the Waller occupation of the house.

The second planting feature, 01BB-24, had also been cut by modern disturbances (see Figure 3). Located approximately 2.2 m east of the front porch, only a small section, RR168203 Figure 3. Planting features (Master Context M5). 8 RR168204 Figure 4. Profile of planing feature 01BB-12. approximately 50 x 47 cm, was left. Most of the feature had been removed by Jimmy Knight trench 01BB-22 and modern planting feature 01BB-10. Like 01BB-12, 01BB-24 was roughly circular in shape, though again its true boundaries were impossible to determine due to modern intrusion. Planting hole 01BB-24 also had an irregular profile, similar to that of 01BB-12, and lacked a postmold (Figure 5). It also contained a large root stain at the bottom, most likely representing a primary root. The hole was approximately 35-40 cm deep and contained a similar fill to planting hole 01BB-12. Several artifacts were recovered, including wine bottle and window glass, nails, and bone. No TPQ date could be established for the feature.

Planting feature 01BB-26 was located approximately 4 m from the front porch of the Waller House (see Figure 3). Again, it should be noted that distances from the porch are approximate, as only portions of the features remained. Feature 01BB-26 was cut both by Jimmy Knight trench 01BB-30 and 1950s archaeological fill (context M2). Only 40 x 15 cm remained of 01BB-26. Like the previously discussed planting features, it was slightly mottled and contained a friable sandy clay loam fill. Its profile was also irregular and ranged in depth from 15 to 40 cm, with the eastern edge being slightly shallower than the western. Like 01BB-12 and 01BB-24, a root stain appeared in subsoil at the bottom of 01BB-26. The only artifacts recovered from planting feature 01BB-26 were brick chunks. The lower concentration of artifacts in this feature is most likely due to the fact that a much smaller segment of the feature remained to be excavated.

The last of the planting features on the east side of the front porch was 01BB-90 (see Figure 3). Located approximately 6.2 m from the front porch, 01BB-90 was cut by modern archaeology fill M2, yet more of it remained than with any of the other planting features located east of the front porch. A full 225 x 52 cm remained to be excavated. The feature, as with the previous planting features, was cut along the north by the excavation sidewall. 9 RR168205 Figure 5. Profile of planting feature 01BB-24. This feature was slightly drier than the previous features. The fill was similar, though with a slightly higher clay content than the previous fills. This makes sense, because the entire area would have been disturbed by the installation of the brick arch drain which is located just 60 cm to the south. This profile was also irregular, but had also been disturbed by a large, modern tree root which was still extant at the beginning of the digging process (Figure 6). The feature was approximately 40 cm deep, and as with the previous features contained a large root stain at the bottom. Artifacts included, among others, nails, brick, and a fragment of dipped white salt glazed stoneware which provided a TPQ of 1715.

Fewer features in this line of planting features survived to the west of the porch. This was due to the fact that most of the area west of the porch had been previously dug by Jimmy Knight in the 1950s. Planting feature 01BB-57 lay approximately 50 cm to the west of the front porch steps (see Figure 3). It had been cut by Jimmy Knight trench 01BB-45, and like the features to the east of the porch was cut by the north wall of the excavation trench. Approximately 40 x 45 cm remained to be excavated. Again, the feature was vaguely circular in shape where it could still be seen. The fill was again a slightly mottled friable sandy clay loam. The profile of feature 01BB-57 was the most irregular, and most likely represented two planting features with one having been removed and the other placed directly in its removal hole (Figure 7). Due to the nature of planting holes, and their inherent irregularity, it was impossible to determine the extent of each individual planting hole. The two were excavated together, with changes in fill and profile shape noted on the context form. Feature 01BB-57 was approximately 47 cm deep, with two extensions on either side of a shallower depression. Artifacts recovered included bricks, nails, wine bottle, bone, and white salt glaze stoneware which provided at TPQ of 1720.

The only other surviving planting feature to the west of the porch was feature 01BB-72, located approximately 3.8 m from the front porch of the Waller House. Feature 01BB-72 was cut by historic features 01BB-70 and 01BB-68 and also by the north wall of the archaeological excavation trench. Its fill was slightly darker and less mottled than the previously discussed features, but it too was a lightly mottled sandy clay loam, approximately 10 RR168206 Figure 6. Profile of planting feature 01BB-90. RR168207 Figure 7. Profile of planting feature 01BB-57. 40 cm deep and with the same root stain located in subsoil at the bottom of the feature. The profile was also irregular with a slight step on the eastern edge of the feature. A TPQ of 1720 was established by white salt-glazed stoneware. Other artifacts removed included, but were not limited to, tobacco pipes, mirror glass, brick, bones, and an upholstery tack.

The 1782 Desandrouins map indicated that there were indeed bushes of some type in front of the Waller House at that time. However, while it is possible that the planting features excavated in spring 2000 dated to the 1780s, their earlier TPQ dates point to a more likely planting date sometime around mid-century. It is possible, and even likely, that these same plants or bushes were still standing in the 1780s or that they had been replaced with similar decorative shrubbery. While archaeologists were not able to determine the exact species which grew along the front of the Waller House, they were able to state with certainty that, like other middling gentry men of the time, Benjamin Waller was concerned that his property be aesthetically pleasing to his peers. This can also be seen in the elaborate show gardens which were planted and maintained behind the Waller home (Schlesinger 1980).

11
Layer (Master Context M6)

Only one layer which archaeologists could definitively date to the Waller period survived along the north face of the house. Located in the northwest excavation trench, layer M6 had a TPQ of 1775 established by pearlware (Figure 8). It also contained creamware, porcelain, table, wine bottle and window glass, shell, nails and other examples of the standard domestic artifacts generally found by archaeologists in the vicinity of middling gentry homes. The finds list for this layer (see Appendix B) is small, however, because the layer had been almost entirely cut away by both historic and modern features.

The historic features may in fact have actually been contemporaneous with the layer. This was impossible to determine since modern archaeological trenches and planting features had destroyed the archaeological interface between the layer and the Waller-era landscaping features (M5). It is, however, likely that the layer and the features were both extant during Benjamin Waller's occupation of the house. Both the TPQ dates and the stratigraphic relationships which appear to exist between the two support such a conclusions.

The modern archaeological excavation trenches played an active role in the destruction of layer M6. Jimmy Knight trenches cut across the layer in several places. In addition, the 1950s waterproofing trench, M8, also cut the layer, destroying the southern portion of the layer.

The two meters which surround the Waller House have, for the past 250 years, been a high activity area. Archaeologists encountered abundant evidence of landscaping activities, from the Waller era to the present day. This layer is an example of the high priority placed on the house and its immediate surroundings. Layer M6 was criss-crossed with planting and removal features, indicative of the continually changing landscape around the Waller House.

Decorative landscaping, like that in along the north face of the Waller House, was an activity of the gentry class. Throughout his life, Benjamin Waller made an effort to live as an example of middling gentryhood (Greenman 1994). The elaborate Waller gardens, as illustrated by Benjamin Waller's granddaughter Eliza Waller in 1791 (Figure 9), are another RR168208 Figure 8. Plan view of layer M6. 12 RR168209 Figure 9. Possible plan of Waller garden (Map is titled "Plan of Tower HILL, Sussex County, believed to be a replica of the Benjamin Waller garden at Williamsburg, VA.). example of Waller's desire to be like the gentry men he befriended-Secretary Carter and Peyton Randolph, for example. So then would the Waller drain which will be discussed later in this report.

Shell Midden 01BB-109 and Related Layers

Shell midden 01BB-109 was located in the excavation trench along the west wall of the main wing of the house. The midden and the three layers which it sealed (01BB-111, 01BB-129, and 01BB-149) were all that was left of the Benjamin Waller era on the west side of the house. In fact, they were all that was left of any pre-1950 strata. The standard 50-cm-wide waterproofing trench ran all the way along the west wall of the house. In 13 addition, the original lightning rod, which still stands against the house today in most of its original form, was entirely excavated in the 1950s, destroying most of the stratigraphy around it. Early in 2000, a new waterline was buried in the Waller yard, cutting away the westernmost portion of the excavation trench.

Shell midden 01BB-109 was located in the most southwestern corner of the excavation trench (Figure 10). The midden consisted of hundreds of whole oyster shells along with 1030 pieces of animal bone and myriad early to mid-eighteenth-century artifacts, including delftware, pearlware, white salt glazed stoneware, Chinese porcelain, pipe stems, table, window, wine bottle, and pharmaceutical glass, window leads, an upholstery tack, and wrought nails, among others. The midden was 92 x 33-90 cm and irregular in shape. It was fairly shallow, reaching a depth of only 5 cm. Its irregular nature, combined with its shallowness, lead to its interpretation as a midden or as sheet refuse rather than a trash pit. The midden's contents were fairly typical for domestic trash refuse, though its location on the opposite end of the house from the kitchen (both the kitchen outbuilding and the later interior kitchen were to the west) raised questions. Why the occupants of the house were traveling across the back yard to dump trash is still an open question.

The midden appears to have been used for a fairly short period of time as it is relatively shallow and not overly large in area. It was impossible to determine the true size of the midden due to the fact that it abutted a large tree stump to the south and was cut by the excavation wall to the west. However, its TPQ of 1775 indicates that it was in use during Benjamin Waller's occupation of the house.

Shell midden 01BB-109 sealed three layers-01BB-111, 01BB-129 and 01BB-149. None of theses layers contained any where near the quantity of artifacts recovered from the shell midden. The three layers abutted a modern utility trench and were also heavily disturbed by roots from the nearby stump. They likely experienced some degree of RR168210 Figure 10. Plan of shell maiden 01BB-109. 14 contamination due to these disturbances. Still, the layers contained artifacts largely dating to the mid-eighteenth century. Layer 01BB-111 was a brown sandy loam nine centimeters deep containing delftware, pearlware, Colonoware, tobacco pipes, white salt glazed stoneware, window, wine bottle, pharmaceutical, and table glass, wrought nails, 99 bone fragments, and oyster shell, among others. It sealed layer 01BB-129, which was a reddish brown sandy loam six centimeters deep and almost entirely sterile except for a few brick inclusions. Layer 01BB-129 in turn sealed layer 01BB-149, a mottled reddish brown sandy loam 13-17 cm deep containing delftware, pearlware, window and wine bottle glass, and one bone. Layer 01BB-149 sealed sterile subsoil.

These layers most likely accumulated over the course of Benjamin Waller's occupancy. They then served as the base for the small shell midden which built up on the southwest corner of the house. Although small backyard middens are not uncommon in Williamsburg at this time, the location of the midden so far from the kitchen is an interesting oddity. Exactly why this spot was chosen as a dump site remains unclear. However, the Wallers were clearly using this area as a place for disposing of domestic refuse.

Planting Features 01BB-146, 01BB-155, 01BB-158

Few features dating to the Waller occupation remained intact in the trench which ran along the south wall of the house's main wing. The construction and subsequent removal of a Victorian-era porch had obliterated most of the cultural layers and features behind the house. Additionally, the 1950s renovations and waterproofing of the foundation had done damage as well, especially to the area within 50 centimeters of the foundation. However, there were some features which were contemporaneous with the Benjamin Waller years.

Three planting features which dated to Benjamin Waller's occupation of the house were in evidence along the south wall of the House. The features did not appear to relate to one another. The first of these, feature 01BB-146, cut into subsoil (Figure 11). Most likely it was sealed by Waller occupation layer M7 (see below). However, in this area all stratigraphy had been destroyed by the Victorian-era porch. In addition, the feature extended outside the excavation area and was cut away by the south boundary of the excavation trench. Once the modern fill from the porch removal had been excavated, the feature was visible in subsoil.

Planting feature 01BB-146 was roughly circular in shape, 54 x 40 cm, and reached a depth of 50 cm. The fill was a friable sandy clay loam. There were numerous artifacts within the fill, though none which provided a TPQ. Delftware, Colonoware, tobacco pipes, window glass and table glass were all removed during excavation, along with several other artifacts. Although no TPQ was established, the assemblage appeared to be mid-eighteenth century, which would have dated the planting feature to the Benjamin Waller period. No other features which related to 01BB-146 were uncovered.

Feature 01BB-155 was a very shallow planting hole which cut Waller occupation layer M7 (Figure 12). The feature appeared after the removal of layer M8 which had been contaminated during the 1950s excavations when workmen walked over the layer, pressing modern artifacts into the soft dirt. The feature was relatively small and shallow (34 x 44 x 13 cm) and had been disturbed by roots. The fill was a yellowish brown sandy 15 RR168211 Figure 11. Plan of planting feature 01BB-146. RR168212 Figure 12. Profile of planting feature 01BB-155. loam. Artifacts recovered during excavations included North Midlands slipware (providing a TPQ of 1670), window and wine bottle glass, and a piece of quartz debitage. Although the TPQ is very early, the feature cuts layer 01BB-160, which has a TPQ of 1762, meaning that the feature could not have been deposited prior to 1762.

Planting feature 01BB-158 was larger than the other two rear planting features and had previously been covered by the Victorian-era porch (Figure 13). The feature was 61 x 58 x 22 cm and consisted of a grey sandy loam. Several small root holes which were 16 RR168213 Figure 13. Plan view of layer M7. most likely related to the planting itself were in evidence. No diagnostic artifacts which would provide a TPQ date were recovered. However, there were Chinese porcelain sherds, wine bottle glass, and wrought nails in the feature fill, suggesting it dated to the Benjamin Waller occupation period.

Layer (Master Context M7)

Only one layer relating to the Waller occupation was excavated in the rear of the house, along the south wall of the main wing (Figure 13). Like layer M6 it had been cut by both modern and historic features. The entire northern portion of the layer was destroyed during the 1950s waterproofing, as again was the Waller House builder's trench. The eastern section of the layer was cut away by the construction and subsequent removal of a Victorian-era porch. In addition, before Layer M7 could be investigated, a layer which had been contaminated during the 1950s refurbishing of the house (layer M9, see below) had to be removed. Layer M8 appears to have been contemporaneous with Benjamin Waller's residence at the House.

The layer was most likely a living surface during the time of Waller's occupation. Artifact concentrations were moderate, similar to layer M6 along the north face of the house (see above). Finds were of a domestic nature in keeping with the layer's proximity to the house. Some of those finds included delftware, creamware (which provided a TPQ of 1762 for the layer), tobacco pipes, Colonoware, Chinese porcelain, table glass, bottle glass, case bottle glass, dry-bodied stone ware, and wrought nails, among others.

Most of the intrusions into layer M7 were modern. So little was left of the layer that it is impossible to say much about it other than that its artifact content was typical of a mid-eighteenth century domestic layer.

Scaffolding Features 01BB-168 and 01BB-175

Only two features which may relate to the Benjamin Waller occupation period were located along the west face of the "L" wing, which was constructed sometime around 1781, 17 just five years before Benjamin Waller died. As with most areas surrounding the house, most of the stratigraphy had been cut away by modern intrusions. In the case of the west side of the "L" wing, most of the damage had been caused by nineteenth-century boxwoods which were removed in the 1990s when the rear yard and garden of the Waller house were re-landscaped. Large planting stains remained over most of the excavation area. However, in an unexpected development the waterproofing system employed by the 1950s waterproofers changed about half way through the west wall of the "L" wing. Rather than digging a 50-cm-wide trench, they switched to a very narrow trench, around 10 cm wide, into which they simply poured the cement waterproofing agent. Unfortunately, while this method destroyed less of the stratigraphy around the house, it still completely obliterated the original builder's trench.

The two features which did remain, 01BB-168 and 01BB-175, were most likely related to the construction of the "L" wing. Although archaeologists and architectural historians have not been able to determine exactly when the "L" wing was constructed, the Frenchman's Map, which was drawn in 1782, shows the Waller house complete with "L" wing. It is likely that the wing was constructed sometime just prior to that. Dendrochronology was conducted throughout the house and may provide answers as to when the different sections of the house were constructed. However, as of early 2001 results of this testing have still not been received by the Foundation.

The two scaffolding holes are roughly similar in size and shape, although 01BB-175 is larger and they are on different orientations (Figure 14). Scaffolding hole 01BB-168 was 30 x 20 x 5 cm and was oriented east-west. Scaffolding hole 01BB-175 was 45 x 26 x 17 cm and was oriented north-south. Within the fill of the scaffolding hole was a stain related to the actual scaffolding itself (01BB-174). There was no similar stain in scaffolding hole 01BB-168, possibly due to disturbances by a modern driven stake. The only artifacts recovered were from context 01BB-175. They included window glass, bone, and a wrought nail, none of which provided a TPQ date.

RR168214 Figure 14. Plan view of features 01BB-168 and 01BB-175.

Layer (Master Context M10)

For the most part the rest of the area around the "L" wing had been destroyed during the 1950s waterproofing and restoration. What little soil did remain had been heavily cross-trenched by Jimmy Knight and was also cut with modern utility trenches. A small portion of an early layer was in evidence on both the south and east elevations of the "L" (Figure 15). So little remained, however, that it is difficult to say much about the layer. Few artifacts were removed, including 18 window and wine bottle glass, bone, and one wrought nail. No TPQ was available but stratigraphic relationships would tend to imply that the layer is most likely Waller era.

RR168215 Figure 15. Plan view of layer M10.

The Brick Arch Drain

Without a doubt the most interesting feature encountered during the 2000 archaeological excavations of the Waller House was the brick arch drain which extended from the northeast portion of the house past the Office and continued on in a northeasterly direction (Figures 16 and 17). Although the drain had been previously uncovered during Jimmy Knight's 1950s excavations, little was known about the function of the drain.

1950s Excavations

In 1950 Jimmy Knight's crew uncovered the brick arch drain while excavating prior to the waterproofing of the house foundation. At that point the drain connected to the house and then made a sharp turn to the northeast. Knight excavated as far as the office, where the drain had been broken away and thus appeared to terminate. However, the rough nature of the break indicates that the drain did in fact at one point continue on past the office, although how far it extended is still not known.

In order to complete waterproofing and repair activities, workmen removed the section of the drain which attached to the house (an approximately three foot section) and bricked up the southern end of the drain. A rough outline of the drain's entry into the basement was outlined in brick on the foundation in order to provide future investigators with an idea of how the drain was originally connected. Unfortunately, there was error in the both the height and width of the drain when it was outlined on the wall. It is apparent to the naked eye that the drain is larger than the outline indicates. Subsequent measurements confirmed this error, and this was taken into consideration when archaeologists began to speculate about the function of the drain.

19

RR168216 Figure 16. Plan of vaulted brick drain.

RR168217 Figure 17. Profile of vaulted brick drain.

20
Drain Form

The drain is nine courses high not including the arch (see Figure 17). The arch extends another five courses for a total inside height of approximately 90 cm. The inside of the drain is roughly 60 cm across. The outside measurements are 1 x 1.6 m. The total length of the drain is not known as it has never been entirely excavated.

Three types of drains were typically used in eighteenth-century Williamsburg. The simplest of these was knows as the gutter or French drain. A simple V formed by two rows of bricks served to drain rainwater run-off to lower ground or into larger underground drains through drain boxes (Gilmore 1998). More complex than the open French drains were the enclosed box drains. These consisted of two parallel rows of headers laid into a trench. Walls were made up of two courses of stretchers placed less than one brick width apart. This formed a brick-lined trench which was then covered with additional stretchers. These drains were used to remove water from basements and generally fed into larger vaulted drains (Gilmore 1998). The largest and most complex drains common to Williamsburg were the vaulted brick drains, or brick arch drains, like the one uncovered at the Waller House. Found throughout the Historic Area, these drains were commonly constructed by digging a deep trench and then lining the bottom and sides with bricks. Builders then constructed a vaulted roof to cover these drains. They were commonly found in close proximity to either kitchens, wells, or both, though they are found in many locations throughout Williamsburg. Their massive size (1'8" to over 3' wide) which made them the backbone of Williamsburg's complex drainage system (Gilmore 1998).

Clearly the Waller drain does not fit this typical model. If it had, it a simple box drain would have sufficed for removal of water from the Waller basement. This box drain would then have deposited water from the basement into a larger vaulted drain, similar to the Waller drain. However, this was not the case.

The Waller drain is one of the largest to be uncovered in the Historic Area and is by far the largest drain which leads out of a private dwelling. Although several other buildings do have drains in order to remove water from their basements (i.e., the Governor's Palace and the Anderson House), none compare in size to the Waller drain. This poses a very interesting question: What function of the Waller drain required that it be so large? The answer to that question has eluded scholars, though through combined effort, several plausible explanations have been proffered.

Drain Function

Drains provided two major functions in eighteenth-century Williamsburg. First, they served to drain the streets and low-lying lots within the city, making it not only more inhabitable and traversable, but also considerably more aesthetically pleasing. Second, they served to drain water and liquid waste from many of the buildings throughout the city. Typically, the simpler French and box drains lead from houses and outbuildings and then deposited their liquid into larger underground brick arch drains. This was the case at the Governor's Palace, the Anderson property, and the Public Hospital, among others. However, this was not the case at the Waller House. Rather than constructing a small box drain which then either dumped into a nearby ravine, or into the city's vaulted drain system, Waller constructed 21 one of the largest drains to be uncovered by archaeologists in the city, and he attached it to his house.

Two major stumbling blocks exist which impede our understanding of the Waller drain. The first of these is the lack of any documentary evidence which alludes to the construction of the drain. Humphrey Harwood, who did most of the subsequent repairs to the Waller House, makes no mention in his ledger of either the construction of the Waller House or its drain. Waller himself left behind no memoirs, nothing to indicate what he was thinking as he had the drain constructed. Secondly, the Waller drain has never been fully excavated. Archaeologists do not know how far the drain extends or whether it continues in the same northeasterly direction until its terminus. Archaeologists have twice explored the section of the drain closest to the house, but have yet to see the true terminus of the drain.

These stumbling blocks have not kept archaeologists, or their fellow scholars, from speculating about the size and function of the Waller drain. It is the consensus of archaeologists, historians, and architectural historians that the Waller drain was indeed constructed to remove water from the Waller House basement. The question then remains, why construct such a large drain for water removal when clearly a much smaller drain would suffice.

The most likely theory as to why Benjamin Waller had such a large drain constructed has to do with his acquisition of large tracts of land to the east of the Capitol Building. As discussed in the historical section of this report, Benjamin Waller saw himself as the quintessential gentleman. He worked hard at establishing himself as one of the more prominent residents of the capital city. As part of this, he acquired most of the lots of land east of what is now Waller Street, where Christiana Campbell's Tavern now stands, diagonally across Francis Street from his own house. He intended to establish a neighborhood or subdivision in this area, selling off the lots to individuals who would then build houses upon them. He may then have seen his drain as potentially the main feeder drain for an entire network used to drain the basements and low-lying areas in this new neighborhood. This then would explain the size of the drain, if potentially one day it were to carry the waste water and run-off of an entire subdivision.

In fact, Waller did accumulate this land, clearly with the intention of selling it off, which he began doing as early as the 1750s. In addition, the Frenchman's Map shows some type of barrier extending into Francis Street just to the west of the Waller House (Figure 18), effectively separating the Waller House from the rest of the street. Perhaps this was also intended to set the Waller subdivision off from the surrounding area. This barrier, combined with the route of Waller Street and the placement of buildings along its east side, provided Waller with a vista, something much coveted by the Williamsburg wealthy and increasingly hard to come by as the city bulged and lots became scarcer and scarcer.

It is likely that Waller's subdivision came to fruition. The historical record indicates that Benjamin Waller was quite successful in selling the land he had acquired east of the Capitol (Stephenson 1950). At some later point, the subdivision was annexed into the city and became part of Williamsburg proper. This being true, it is also likely that the Waller drain does in fact continue, crossing under Francis Street and possibly intersecting with 22 other drains on the lots between Francis and Lafayette Streets. Archaeological investigation of the "Waller" subdivision would answer any remaining questions regarding the Waller drain and the network of drains for which it served as the primary repository.

Post-Benjamin Waller Era Features

There were several interesting features which postdated Benjamin Waller's occupation of the house. Although most of the post-Waller era finds consisted of past archaeology and landscaping fill, there were some features which provided information regarding the house after 1786.

Nineteenth-Century Foundation 01BB-152

Although foundation 01BB-152 had clearly been encountered by Jimmy Knight in his 1950s excavations, no mention was made of it in any subsequent reports relating to the Waller House excavations or renovations. Located in the excavation trench along the south wall of the main wing of the house, foundation 01BB-152 was covered with debris from the 1950s renovations, mainly plaster and mortar. Some 2.38 m (7.8 feet) long (eight stretchers and six headers) and 11 cm (4.3 inches, ½ course) wide, the foundation was constructed in English bond using sand mortar (Figure 19).

The foundation was cut well into subsoil, the bottom courses (in most cases all that was left) were located 64 cm below the ground surface. The eastern portion of the foundation consisted of three courses of brick which reduced to two and then one as it moved west (Figure 20). The foundation did not appear to turn, but consisted of a simple straight line of bricks a half-course wide. The north face of the foundation abutted the 1950s waterproofing trench, the south face subsoil. It is possible and even likely that part of the 23 RR168219 Figure 19. Plan view of foundation 01BB-152. RR168220 Figure 20. Profile of foundation 01BB-152. foundation was destroyed during Jimmy Knight's excavations. Without further information, it is impossible to understand the function of the foundation. It is possible that it was some sort of retaining wall, but any explanation for its existence would at this point be conjecture. Neither archaeologists nor architectural historians were able to decipher its function.

Layer (Master Context M9)

Layer M9 sealed layer M7, the Benjamin Waller era layer along the south wall of the main wing (see Figure 13). Layer M9 was possibly a turn-of-the-century layer, with a TPQ of 24 1880 established by manganese solarized glass. In addition it contained delftware, creamware, North Midlands slip, Yorktown-type earthenware, Colonoware, Chinese porcelain, a crucible fragment, window, wine bottle, table, and pharmaceutical glass, case bottle, pipe stems, bone, and wrought nails. The layer may have in fact dated to the Benjamin Waller era, but during renovations it was exposed to constant trampling by workers, thus contaminating it and giving it a much later TPQ.

The scarcity of late nineteenth-century artifacts and the plethora of mid eighteenth-century artifacts, along with a fair amount of plaster seemingly crushed into the layer (perhaps by workers' feet?) reinforce this conclusion. However, as the layer does date to the late nineteenth century and can not be definitively attributed to the Benjamin Waller era, it was labeled as a post-Benjamin Waller era layer.

Victorian Porch (Master Context M11)

Although it was removed during the 1950s restoration, remnants of a Victorian-era porch still existed along the south wall of the main wing of the house. Extending from the south wall of the house was a section of one of the original foundation walls which had been capped in concrete (01BB-132). A second section of foundation wall (01BB-140) ran east-west and represented the southern extent of the Victorian porch. However, only a soil stain remained of this section of porch, as the bricks had been entirely removed rather than capped. In 1950 this Victorian-era porch connected with the rear porch which is still in existence today. It was removed and capped in concrete, leaving behind only the stains which archaeologists uncovered during the 2000 excavations.

The majority of remaining post-Waller features were related to the 1950s archaeology and renovations or to post-1950s landscaping. Other than providing archaeologists with the challenge of trying to decipher their functions and separating them from historic contexts, these features have little to teach us about the Benjamin Waller occupancy of the House. What they do indicate is that the Waller House has continued to be the site of much activity, from its original construction sometime in the mid-eighteenth century through the ongoing renovations of the new century.

25

Chapter 3.
Conclusions

Much of the information surrounding the Waller House had been destroyed by previous archaeology, renovation activities, and modern landscaping. This, combined with the small size of the excavation area, restricts the conclusions which can be drawn concerning Benjamin Waller's occupation of the house. However, enough was left behind to help us to better understand not just Benjamin Waller, but the direction in which the city of Williamsburg was heading as it passed the mid-century mark and headed toward the post-Revolutionary era.

By mid-century Williamsburg's best lots had been sold and people who wished to live in the city were forced into the outlying areas, often onto lots which were poorly drained and separated from the city's major social and economic arenas (Gilmore 1998; Reps 1972). Waller's successful attempt to create a subdivision, which would be drained by a complex system similar to that at Anderson Forge, clearly addressed these issues. The most sought-after lots having been sold, he provided a new direction in which the city could grow. With people in residence, new enclaves grew up around these outlying areas. While early in the eighteenth century the area east of the Capitol was little more than pasture land, after Waller began selling off lots it developed into an urban area complete with taverns and other entertainment venues, such as the Hallam Theater. Eventually, it would be annexed into the city, subsumed within the boundaries of Williamsburg.

Benjamin Waller was indeed an exemplary citizen, the ideal gentlemen. Archeological and historical explorations into his past have revealed him as a man intensely concerned with appearances who continually improved upon his home, created a subdivision on the east end of town, and built one of the largest brick arched drains in the city. Though much information about Benjamin Waller has been lost through time, much was learned through the course of this project, and many new avenues of research were opened.

26

Bibliography

Gilmore, Grant
1998
Phase II Archaeological Investigations of Block 8, Area G in the Colonial District. Manuscript, Department of Archaeological Research, Colonial Williamsburg Foundation, Williamsburg, VA.
Greenman, John Starr
1994
The Rise of Benjamin Waller: 1716-1786. Master's thesis, The College of William & Mary, Williamsburg, VA.
Heaton, Lynda Rees (transcriber and editor)
1967
Littleton Waller Tazewell's Sketch of His Own Family 1823. Master's thesis, The College of William & Mary, Williamsburg, VA.
Hening, William Waller
1969
The Statutes at Large: Being a Collection of all the Laws of Virginia, from the First Session of the Legislature, in the Year 1619. 13 Vols. University Press of Virginia, Charlottesville, VA.
Reps, John William
1972
Tidewater Towns: City Planning in Colonial Virginia and Maryland. The Colonial Williamsburg Foundation, Williamsburg, VA.
Schlesinger, Catherine
1980
James Geddy House and Shop: Interpretive Paper. Colonial Williamsburg Library Research Report Series RR-260. The John D. Rockefeller Jr. Library, Colonial Williamsburg Foundation, Williamsburg, VA.
Stephenson, Mary
1950
Benjamin Waller House History. Manuscript, The John D. Rockefeller Jr. Library, Colonial Williamsburg Foundation, Williamsburg, VA.
Virginia Gazette
--
Virginia Gazette. Williamsburg, VA.
27

Appendix A.
Master Context List

Master ContextDescription
M1Topsoil
M2Post-1950 Intrusions
M3Brown Sandy Loam
M4Dark Brown Sandy Loam w/Charcoal and Burn Patches
M5Planting Features
M6Waller-Era Layers
M7South Wall Layers
M81950s Waterproofing Trench
M9Layer Sealing M7
M10Probable Waller-Period Layer
M11Victorian-Era Porch
28

Appendix B.
Artifact Inventory

Note: Inventory is printed from the Re:discovery cataloguing program used by Colonial Williamsburg, manufactured and sold by Re:discovery Software, Charlottesville, Virginia. Brief explanation of terms:

Context No.Arbitrary designation for a particular deposit (layer or feature), consisting of a four-digit "site/area" designation and a five-digit context designation. The site/area for this project is "01BB."
TPQ"Date after which" the layer or feature was deposited, based on the artifact with the latest initial manufacture date. Deposits without a diagnostic artifact have the designation "NDA," or no date available.
ListingThe individual artifact listing includes the catalog "line designation," followed by the number of fragments or pieces, followed by the description.

29
Context No.: 01BB-00001 TPQ: 1887
AA1REFINED EARTHEN, WHITEWARE, FRAGMENT, PRINTED UNDER, PRESS MOLDED, BLUE
AB1REFINED EARTHEN, WHITEWARE, FRAGMENT, UNDECORATED, PRESS MOLDED
AC1PORCELAIN, CH PORCELAIN, FRAGMENT, PAINTED UNDER, WHEEL THROWN, BLUE
AD1CERAMIC, ELEC HARDWARE, INSULATOR
AE1CERAMIC, TOBACCO PIPE, IMPORTED, PRESS MOLDED, STEM, 5/64 INCHES
AF1GLASS, COLORED GLASS, FRAGMENT, TABLE GLASS, WHITE
AG1COPPER ALLOY, COIN, STAMPED METAL, LETTERING/NUMB, obverse - UNITED STATES OF AMERICA / 1887 reverse - ONE CENT
AH1COPPER ALLOY, BUCKLE, SHOE, CAST
AI1IRON ALLOY, UNID HARDWARE, CAST
AJ1BRICK, BRICKETAGE
AK1ALUMINUM, BRACKET, CAST, WITH SCREW HOLE
AL1IRON ALLOY, NAIL, 2 TO 4 IN, CUT
Context No.: 01BB-00002 TPQ: 1935
AA1REFINED EARTHEN, PEARLWARE, FRAGMENT, OTHER MOLD DEC, PAINTED UNDER, PRESS MOLDED, GREEN
AB1REFINED EARTHEN, PEARLWARE, FRAGMENT, PAINTED UNDER, PRESS MOLDED, POLYCHROME
AC1REFINED EARTHEN, WHITEWARE, FRAGMENT, PAINTED UNDER, PRESS MOLDED, POLYCHROME
AD1REFINED EARTHEN, WHITEWARE, FRAGMENT, PRESS MOLDED, MAKER'S MARK, ...LIAM ADAMS.../ ...STALL...
AE15REFINED EARTHEN, WHITEWARE, FRAGMENT, PRESS MOLDED
AF1STONEWARE, AMER BLUE/GREY, FRAGMENT, WHEEL THROWN
AG1STONEWARE, WH SALT-GLAZED, FRAGMENT, WHEEL THROWN
AH1PORCELAIN, CH PORCELAIN, FRAGMENT, PAINTED UNDER, WHEEL THROWN, BLUE
AI1CERAMIC, TOBACCO PIPE, IMPORTED, PRESS MOLDED, STEM, 4/64 INCHES
AJ1STONEWARE, AMER STONEWARE, FRAGMENT, WHEEL THROWN
AK1GLASS, CLRLESS LEAD, FRAGMENT, STEMMED GLASS, EMPONTILLED
AL5GLASS, FRAGMENT, WINE BOTTLE
AM1GLASS, COLORED GLASS, FRAGMENT, BOTTLE, MACHINE-MADE, WHITE
AN2GLASS, FRAGMENT, WINDOW GLASS
AO2BONE, FAUNAL SPECIMEN
AP2ASBESTOS, TILE, ROOFING
AQ1MORTAR, MORTAR, SHELL
AR1LEAD ALLOY, SCRAP
AS1LEAD ALLOY, SCRAP
AT1COPPER ALLOY, CARTRIDGE CASE, STAMPED METAL, LETTERING/NUMB, H, CENTER FIRE
AU1COPPER ALLOY, UNID HARDWARE
AV1IRON ALLOY, UNID HARDWARE
AW1IRON ALLOY, UNID HARDWARE
AX1IRON ALLOY, UNID HARDWARE
AY2IRON ALLOY, NAIL, 2 TO 4 IN, WROUGHT/FORGED
AZ2IRON ALLOY, NAIL, OVER 4 IN, CUT
BA6IRON ALLOY, NAIL, 2 TO 4 IN, WIRE
BB1IRON ALLOY, NAIL, 2 TO 4 IN
30
Context No.: 01BB-00003 TPQ: 1887
AA1COPPER ALLOY, COIN, STAMPED METAL, LETTERING/NUMB, 1887
Context No.: 01BB-00012 TPQ: 1740
AA1REFINED EARTHEN, JACKFIELD-TYPE, FRAGMENT, PRESS MOLDED
AB1PORCELAIN, CH PORCELAIN, FRAGMENT, PAINTED OVER, WHEEL THROWN, RED
AC1PORCELAIN, CH PORCELAIN, FRAGMENT, PAINTED UNDER, WHEEL THROWN, BLUE
AD2CERAMIC, TOBACCO PIPE, IMPORTED, PRESS MOLDED, STEM, 5/64 INCHES
AE2GLASS, CLRLESS LEAD, FRAGMENT, TABLE GLASS
AF2GLASS, COLORED GLASS, FRAGMENT, PHARM BOTTLE, GREEN
AG10GLASS, FRAGMENT, WINE BOTTLE
AH13GLASS, FRAGMENT, WINDOW GLASS
AI1BONE, FAUNAL SPECIMEN
AJ1BONE, COMB, WORKED
AK1SHELL, SHELL, OYSTER
AL1SANDSTONE, FRAGMENT
AM2BRICK, BRICKETAGE
AN1IRON ALLOY, UNID HARDWARE
AO3IRON ALLOY, NAIL, LESS THAN 2 IN, WROUGHT/FORGED
AP3IRON ALLOY, NAIL, 2 TO 4 IN, WROUGHT/FORGED
AQ11IRON ALLOY, NAIL, WROUGHT/FORGED, FRAGMENT
Context No.: 01BB-00017 TPQ: 1850
AA1REFINED EARTHEN, PEARLWARE, FRAGMENT, PAINTED UNDER, BLUE
AB2GLASS, FRAGMENT, WINE BOTTLE
AC1GLASS, FRAGMENT, WINDOW GLASS
AD1GLASS, FRAGMENT, WINDOW GLASS
AE1BRICK, BRICKETAGE
AF3MORTAR, MORTAR, LIME
AG1TINNED CU ALLOY, UNID HARDWARE
AH1IRON ALLOY, UNID HARDWARE
AI2IRON ALLOY, NAIL, LESS THAN 2 IN, CUT
AJ1IRON ALLOY, NAIL, LESS THAN 2 IN, WIRE
AK1IRON ALLOY, NAIL, FRAGMENT
Context No.: 01BB-00024 TPQ: NDA
AA7GLASS, FRAGMENT, WINE BOTTLE
AB2GLASS, FRAGMENT, WINDOW GLASS
AC3BONE, FAUNAL SPECIMEN
AD1BRICK, BRICKETAGE
AE3IRON ALLOY, NAIL, LESS THAN 2 IN
Context No.: 01BB-00026 TPQ: NDA
AA6BRICK, BRICKETAGE
Context No.: 01BB-00028 TPQ: 1715
AA1STONEWARE, DIPPED WSG, FRAGMENT
AB2BRICK, BRICKETAGE, GLAZED
AC2BRICK, BRICKETAGE
AD1IRON ALLOY, UNID HARDWARE
AE2IRON ALLOY, NAIL, 2 TO 4 IN, WROUGHT/FORGED
31
Context No.: 01BB-00036 TPQ: NDA
AA1BRICK, BRICKETAGE
Context No.: 01BB-00047 TPQ: 1850
AA5GLASS, FRAGMENT, WINDOW GLASS
AB4BRICK, BRICKETAGE
AC1IRON ALLOY, NAIL, LESS THAN 2 IN, WIRE
AD1IRON ALLOY, NAIL, FRAGMENT
Context No.: 01BB-00052 TPQ: 1775
AA1REFINED EARTHEN, CREAMWARE, FRAGMENT, PAINTED UNDER, GREEN
AB1REFINED EARTHEN, CREAMWARE, FRAGMENT, UNDECORATED
AC3REFINED EARTHEN, PEARLWARE, FRAGMENT, PRINTED UNDER, BLUE
AD1PORCELAIN, CH PORCELAIN, FRAGMENT, PAINTED UNDER, BLUE
AE1GLASS, CLRLESS LEAD, FRAGMENT, DECANTER/CARAFE, CUT, FLUTED, PANELS
AF2GLASS, CLRLESS LEAD, FRAGMENT
AG1GLASS, COLORED GLASS, FRAGMENT, PHARMACEUTICAL, GREEN
AG8GLASS, CLRLESS NON-LD, FRAGMENT, CONTAINER
AH28GLASS, FRAGMENT, WINDOW GLASS
AI3GLASS, CLRLESS LEAD, FRAGMENT, CONTAINER
AJ1GLASS, COLORED GLASS, FRAGMENT, PHARM BOTTLE, GREEN
AK1GLASS, CLRLESS NON-LD, FRAGMENT, TABLE GLASS, COPPER WHL ENGR
AL1SHELL, SHELL, CLAM
AM1COAL
AN3BRICK, BRICKETAGE
AO2IRON ALLOY, NAIL, FRAGMENT, RECENT FRACTURE INTO 2 PIECES
AP1IRON ALLOY, NAIL, FRAGMENT
AQ1GLASS, CLRLESS NON-LD, FRAGMENT, COPPER WHL ENGR
Context No.: 01BB-00056 TPQ: NDA
AA2GLASS, FRAGMENT, WINDOW GLASS
AB1IRON ALLOY, NAIL, FRAGMENT
Context No.: 01BB-00057 TPQ: NDA
AA1STONEWARE, OTHER STONEW, FRAGMENT, SALT GLAZE, BURNED
AB5GLASS, FRAGMENT, WINE BOTTLE
AC1BONE, FAUNAL SPECIMEN
AD7MARL
AE2BRICK, BRICK BAT, 4 1/4 W, 2 1/2 H (FOR BOTH FRAGMENTS)
AF16BRICK, BRICKETAGE, 8 HAVE NATURAL GLAZE.
AG6IRON ALLOY, NAIL, 2 TO 4 IN, WROUGHT/FORGED
AH1IRON ALLOY, NAIL, LESS THAN 2 IN, WROUGHT/FORGED
AI8IRON ALLOY, NAIL, FRAGMENT
Context No.: 01BB-00063 TPQ: 1850
AA2REFINED EARTHEN, CREAMWARE, FRAGMENT, PRESS MOLDED
AB1PORCELAIN, CH PORCELAIN, FRAGMENT, PAINTED UNDER, WHEEL THROWN, BLUE
AC2GLASS, CLRLESS NON-LD, FRAGMENT
AD2GLASS, COLORED GLASS, FRAGMENT, PHARM BOTTLE, GREEN
AE15GLASS, FRAGMENT, WINDOW GLASS
AF7SLATE, SLATE
32
AG11BRICK, BRICKETAGE
AH4IRON ALLOY, HINGE, FRAGMENT
AI1IRON ALLOY, UNID HARDWARE
AJ1IRON ALLOY, UNID HARDWARE
AK1IRON ALLOY, UNID HARDWARE
AL1IRON ALLOY, NAIL, LESS THAN 2 IN, CUT
AM1IRON ALLOY, NAIL, LESS THAN 2 IN, WIRE
AN4IRON ALLOY, NAIL, FRAGMENT
Context No.: 01BB-00064 TPQ: NDA
AA7COARSE EARTHEN, YORKTOWN-TYPE, FRAGMENT, WHEEL THROWN
AB2GLASS, CLRLESS LEAD, FRAGMENT, TABLE GLASS
AC2GLASS, COLORED GLASS, FRAGMENT, PHARM BOTTLE, GREEN
AD1GLASS, FRAGMENT, WINE BOTTLE, HAND TOOLED FIN
AE8GLASS, FRAGMENT, WINE BOTTLE
AF3GLASS, FRAGMENT, WINDOW GLASS
AG2BONE, FAUNAL SPECIMEN
AH4BRICK, BRICKETAGE
AI1IRON ALLOY, UNID HARDWARE
AJ1IRON ALLOY, UNID HARDWARE
AK3IRON ALLOY, NAIL, LESS THAN 2 IN, WROUGHT/FORGED
AL2IRON ALLOY, NAIL, 2 TO 4 IN, WROUGHT/FORGED
AM4IRON ALLOY, NAIL, FRAGMENT
AN1IRON ALLOY, WIRE, BARBED
Context No.: 01BB-00070 TPQ: NDA
AA1EARTHENWARE, DELFTWARE ENG, FRAGMENT, UNDECORATED, WHEEL THROWN
AB2COARSE EARTHEN, YORKTOWN-TYPE, FRAGMENT, WHEEL THROWN
AC2GLASS, CLRLESS LEAD, FRAGMENT, TABLE GLASS
AD2GLASS, FRAGMENT, WINDOW GLASS
AE10GLASS, FRAGMENT, WINE BOTTLE
AF1MORTAR, FRAGMENT, SHELL
AG1GLASS, FRAGMENT, WINE BOTTLE
AH1IRON ALLOY, NAIL, FRAGMENT
Context No.: 01BB-00072 TPQ: 1720
AA2EARTHENWARE, DELFTWARE ENG, FRAGMENT, PAINTED UNDER, WHEEL THROWN, BLUE
AB1CERAMIC, TOBACCO PIPE, IMPORTED, PRESS MOLDED, STEM, 4/64 INCHES
AC2CERAMIC, TOBACCO PIPE, IMPORTED, PRESS MOLDED, BOWL
AD1GLASS, CLRLESS LEAD, FRAGMENT, TABLE GLASS
AE1GLASS, CLRLESS LEAD, FRAGMENT, MIRROR
AF8GLASS, FRAGMENT, WINE BOTTLE
AG14GLASS, FRAGMENT, WINDOW GLASS
AH8BRICK, BRICKETAGE, GLAZED
AI4MORTAR, MORTAR, SHELL
AJ1IRON ALLOY, UNID HARDWARE
AK1IRON ALLOY, UNID HARDWARE
AL2IRON ALLOY, NAIL, LESS THAN 2 IN, WROUGHT/FORGED
AM4IRON ALLOY, NAIL, FRAGMENT
AN1STONEWARE, WH SALT-GLAZED, FRAGMENT
AO3GLASS, COLORED GLASS, FRAGMENT, PHARMACEUTICAL, AQUA
AP1GLASS, COLORED GLASS, FRAGMENT, CONTAINER, OTHER COLOR, YELLOWISH GREEN
AQ5BONE, FAUNAL SPECIMEN
33
AR1COPPER ALLOY, UPHOLSTERY TACK
AS19IRON ALLOY, NAIL, FRAGMENT
Context No.: 01BB-00074 TPQ: NDA
AA1BRICK, BRICKETAGE, GLAZED
AB1IRON ALLOY, NAIL, 2 TO 4 IN, WROUGHT/FORGED
AC1IRON ALLOY, NAIL, WROUGHT/FORGED, FRAGMENT
Context No.: 01BB-00076 TPQ: NDA
AA1PORCELAIN, OTHER PORC, FRAGMENT, PROBABLY CHINESE
AB1GLASS, FRAGMENT, WINDOW GLASS
AC1GLASS, CLRLESS NON-LD, FRAGMENT, CONTAINER
AD1COAL, COAL
AE1SHELL, MARL
AF3SHELL, FRAGMENT, UNIDENTIFIED
AG2BRICK, BRICKETAGE
AH2IRON ALLOY, NAIL, FRAGMENT
Context No.: 01BB-00078 TPQ: NDA
AA3GLASS, CLRLESS LEAD, FRAGMENT, TABLE GLASS
AB2BRICK, BRICKETAGE
Context No.: 01BB-00080 TPQ: NDA
AA2BRICK, BRICKETAGE, GLAZED
Context No.: 01BB-00083 TPQ: NDA
AA2GLASS, FRAGMENT, WINDOW GLASS
AB1BRICK, BRICKETAGE, GLAZED
Context No.: 01BB-00086 TPQ: NDA
AA1BONE, FAUNAL SPECIMEN
AB1BRICK, BRICKETAGE
AC1BRICK, NAIL, FRAGMENT
Context No.: 01BB-00090 TPQ: NDA
AA1IRON ALLOY, UNID HARDWARE
AB2IRON ALLOY, NAIL, LESS THAN 2 IN, WROUGHT/FORGED
AC8IRON ALLOY, NAIL, FRAGMENT
Context No.: 01BB-00094 TPQ: NDA
AA4GLASS, FRAGMENT, WINDOW GLASS
AB1IRON ALLOY, NAIL, 2 TO 4 IN, WROUGHT/FORGED
Context No.: 01BB-00099 TPQ: 1820
AA1REFINED EARTHEN, PEARLWARE, FRAGMENT, PRINTED UNDER, BLUE
AB1REFINED EARTHEN, WHITEWARE, FRAGMENT
AC1IRON ALLOY, NAIL, LESS THAN 2 IN, WROUGHT/FORGED
AD4IRON ALLOY, NAIL, FRAGMENT
Context No.: 01BB-00101 TPQ: NDA
AA1EARTHENWARE, DELFTWARE ENG, FRAGMENT
AB6GLASS, FRAGMENT, WINE BOTTLE
34
AC1GLASS, FRAGMENT, WINDOW GLASS
AD2IRON ALLOY, NAIL, FRAGMENT
Context No.: 01BB-00109 TPQ: 1775
AA1EARTHENWARE, DELFTWARE ENG, FRAGMENT, PAINTED UNDER, POLYCHROME
AB13EARTHENWARE, DELFTWARE ENG, FRAGMENT, PAINTED UNDER, BLUE
AC24EARTHENWARE, DELFTWARE ENG, FRAGMENT
AD16EARTHENWARE, DELFTWARE ENG, FRAGMENT, MISSING GLAZE
AE11DETACHED GLAZE, TIN ENAMELLED, FRAGMENT, PAINTED UNDER, BLUE
AF4DETACHED GLAZE, TIN ENAMELLED, FRAGMENT
AG1REFINED EARTHEN, PEARLWARE, FRAGMENT, PAINTED UNDER, BLUE
AH1REFINED EARTHEN, PEARLWARE, FRAGMENT, PRINTED UNDER, BLUE
AI1REFINED EARTHEN, PEARLWARE, FRAGMENT
AJ3COARSE EARTHEN, COLONO WARE, FRAGMENT
AK1STONEWARE, FULHAM SW, FRAGMENT
AL21STONEWARE, WH SALT-GLAZED, FRAGMENT
AM1STONEWARE, WESTERWALD, FRAGMENT
AN1PORCELAIN, CH PORCELAIN, FRAGMENT, PAINTED UNDER, POLYCHROME, IRON OXIDE ALONG RIM.
AO2CERAMIC, TOBACCO PIPE, IMPORTED, PRESS MOLDED, STEM, 6/64 INCHES
AP5CERAMIC, TOBACCO PIPE, IMPORTED, PRESS MOLDED, STEM, 5/64 INCHES
AQ1CERAMIC, TOBACCO PIPE, IMPORTED, PRESS MOLDED, STEM, 4/64 INCHES
AR1CERAMIC, TOBACCO PIPE, IMPORTED, PRESS MOLDED, BOWL, 5/64 INCHES
AS3CERAMIC, TOBACCO PIPE, IMPORTED, PRESS MOLDED, BOWL
AT1GLASS, CLRLESS LEAD, FRAGMENT, TABLE GLASS, BASE
AU1GLASS, CLRLESS LEAD, FRAGMENT, TABLE GLASS, STEM?
AV1GLASS, CLRLESS LEAD, FRAGMENT, FLAT, SURF DEGRADED
AW3GLASS, CLRLESS LEAD, FRAGMENT, MIRROR GLASS
AX1GLASS, CLRLESS LEAD, FRAGMENT, TABLE GLASS, RIM
AY7GLASS, CLRLESS LEAD, FRAGMENT, CONTAINER
AZ1GLASS, FRAGMENT, PHARMACEUTICAL, FR BLOWN/EMPONT, OTHER COLOR, BLUEGREEN; BASE
BA1GLASS, FRAGMENT, PHARMACEUTICAL, GREEN
BB11GLASS, FRAGMENT, PHARMACEUTICAL, OTHER COLOR, BLUEGREEN
BC1GLASS, FRAGMENT, WINE BOTTLE, HAND TOOLED FIN, FINISH, STRING RIM
BD1GLASS, FRAGMENT, WINE BOTTLE, HAND TOOLED FIN, FINISH, V-SHAPED STRING RIM
BE75GLASS, FRAGMENT, WINE BOTTLE
BF120GLASS, FRAGMENT, WINDOW GLASS
BG1030BONE, FAUNAL SPECIMEN
BH2CHARCOAL
BI3LEAD ALLOY, WINDOW LEAD
BJ17IRON ALLOY, NAIL, 2 TO 4 IN, WROUGHT/FORGED
BK19IRON ALLOY, NAIL, LESS THAN 2 IN, WROUGHT/FORGED
BL17IRON ALLOY, NAIL, FRAGMENT
BM1IRON ALLOY, UNID HARDWARE, THIN, FLAT
BN1COPPER ALLOY, UPHOLSTERY TACK, CAST, SMALL, FLAT HEAD
35
Context No.: 01BB-00111 TPQ: 1820
AA3EARTHENWARE, DELFTWARE ENG, FRAGMENT, PAINTED UNDER, BLUE
AB13EARTHENWARE, DELFTWARE ENG, FRAGMENT
AC2EARTHENWARE, DELFTWARE ENG, FRAGMENT, MISSING GLAZE
AD15DETACHED GLAZE, TIN ENAMELLED, FRAGMENT, PAINTED UNDER, BLUE
AE4DETACHED GLAZE, TIN ENAMELLED, FRAGMENT
AF3REFINED EARTHEN, CREAMWARE, FRAGMENT, UNDECORATED
AG1REFINED EARTHEN, PEARLWARE, FRAGMENT, MAKER'S MARK
AH1REFINED EARTHEN, PEARLWARE, FRAGMENT, PRINTED UNDER, BLUE
AI2REFINED EARTHEN, PEARLWARE, FRAGMENT, UNDECORATED
AJ1REFINED EARTHEN, WHITEWARE, FRAGMENT, PRINTED UNDER, BLUE
AK1REFINED EARTHEN, WHITEWARE, FRAGMENT, UNDECORATED
AL1COARSE EARTHEN, COLONO WARE, FRAGMENT
AM1COARSE EARTHEN, YORKTOWN-TYPE, FRAGMENT, CORDONED
AN1COARSE EARTHEN, BK-GZ REDWARE, FRAGMENT
AO1STONEWARE, WH SALT-GLAZED, FRAGMENT, INCISED
AP1STONEWARE, WH SALT-GLAZED, FRAGMENT
AQ1PORCELAIN, CH PORCELAIN, FRAGMENT, PAINTED UNDER, BLUE
AR1CERAMIC, TOBACCO PIPE, IMPORTED, PRESS MOLDED, BOWL
AS5GLASS, CLRLESS LEAD, FRAGMENT, TABLE GLASS, WINE GLASS?
AT8GLASS, CLRLESS LEAD, FRAGMENT, TABLE GLASS
AU5GLASS, COLORED GLASS, FRAGMENT, PHARMACEUTICAL, FR BLOWN/EMPONT, OTHER COLOR, BASE, BLUEGREEN
AV2GLASS, COLORED GLASS, FRAGMENT, PHARMACEUTICAL, GREEN
AW4GLASS, COLORED GLASS, FRAGMENT, PHARMACEUTICAL, OTHER COLOR, BLUEGREEN
AX15GLASS, FRAGMENT, WINDOW GLASS
AY54GLASS, FRAGMENT, WINE BOTTLE
AZ99BONE, FAUNAL SPECIMEN
BA13SHELL, SHELL, OYSTER
BB1COAL, COAL
BC1FRAGMENT, UNIDENTIFIED; BURNED CLAY?
BD3IRON ALLOY, RAZOR, IDENTIFICATION PENDING X-RAY RESULTS
BE2IRON ALLOY, NAIL, 2 TO 4 IN, WROUGHT/FORGED
BF1IRON ALLOY, NAIL, LESS THAN 2 IN, WROUGHT/FORGED
BG3IRON ALLOY, NAIL, FRAGMENT
Context No.: 01BB-00127 TPQ: 1850
AA1REFINED EARTHEN, PEARLWARE, FRAGMENT, PRINTED UNDER, WILLOW PATTERN, PLATTER
AB1REFINED EARTHEN, WHITEWARE, FRAGMENT
AC5REFINED EARTHEN, WHITEWARE, FRAGMENT, PRINTED UNDER, BLUE, MAKER'S MARK, CAMBRIAN, STIPPLE-TYPE TRANSFER PRINT
AD1STONEWARE, AMER BLUE/GREY, FRAGMENT
AE8CERAMIC, FRAGMENT, FLOWERPOT
AF1GLASS, COLORED GLASS, FRAGMENT, CONTAINER, GREEN, POSSIBLE FRENCH WINE BOTTLE SHOULDER
AG4GLASS, FRAGMENT, WINE BOTTLE, RICKETTS/EMPONT, BODY, MAKER'S MARK, "...KETTS & Co GLAS..."
AH79GLASS, FRAGMENT, WINDOW GLASS
AI2BONE, FAUNAL SPECIMEN
AJ1SHELL, SHELL, OYSTER
AK4CHARCOAL
AL1EGGSHELL
36
AM1SLATE, SLATE
AN5PLASTER, PLASTER, WHITEWASH
AO1OTHER INORGANIC, FRAGMENT, BURNED PLASTER?
AP2MORTAR, MORTAR
AQ1IRON ALLOY, NAIL, OVER 4 IN, WIRE
AR65IRON ALLOY, OTHER HARDWARE, CONTAINER, COAL SCUTTLE
AS1IRON ALLOY, UNID HARDWARE, WINDOW GLASS ATTACHED
AT2IRON ALLOY, UNID HARDWARE
AU1IRON ALLOY, OTHER HARDWARE, TOBACCO BOX LID
AV1IRON ALLOY, SPIKE
AW1IRON ALLOY, IRON, FLAT, WROUGHT/FORGED, HANDLE
Context No.: 01BB-00135 TPQ: 1775
AA1EARTHENWARE, DELFTWARE ENG, FRAGMENT, PAINTED UNDER, BLUE
AB1REFINED EARTHEN, PEARLWARE, FRAGMENT, ANNULAR, POLYCHROME
AC2GLASS, FRAGMENT, WINDOW GLASS
AD2GLASS, FRAGMENT, WINE BOTTLE
AE1SHELL, SHELL, OYSTER
AF3MORTAR, MORTAR, SHELL
AG8IRON ALLOY, NAIL, FRAGMENT
Context No.: 01BB-00137 TPQ: NDA
AA1COARSE EARTHEN, COLONO WARE, FRAGMENT
AB2GLASS, FRAGMENT, WINDOW GLASS
AC8GLASS, FRAGMENT, WINE BOTTLE
AD1QUARTZ, DEBITAGE, ANG/BLOCKY FRAG, 1-74% CORTEX
AE1COARSE EARTHEN, YORKTOWN-TYPE, FRAGMENT
AF1IRON ALLOY, NAIL, 2 TO 4 IN, WROUGHT/FORGED
AG3IRON ALLOY, NAIL, FRAGMENT
Context No.: 01BB-00138 TPQ: NDA
AA6MORTAR, MORTAR, SHELL, FRAGMENT
AB1IRON ALLOY, UNID HARDWARE
Context No.: 01BB-00140 TPQ: NDA
AA2BRICK, BRICKETAGE, SPECIALTY BRICK?
AB4MORTAR, MORTAR, LIME
Context No.: 01BB-00143 TPQ: NDA
AA2GLASS, FRAGMENT, WINDOW GLASS
AB1GLASS, FRAGMENT, WINE BOTTLE
AC1IRON ALLOY, NAIL, FRAGMENT
Context No.: 01BB-00145 TPQ: NDA
AA1PORCELAIN, CH PORCELAIN, FRAGMENT, PAINTED UNDER, BLUE
AB6GLASS, FRAGMENT, WINDOW GLASS
AC1BONE, FAUNAL SPECIMEN
AD1BRICK, BRICKETAGE, SPECIALTY BRICK?
Context No.: 01BB-00146 TPQ: NDA
AA2EARTHENWARE, DELFTWARE ENG, FRAGMENT, PAINTED UNDER, BLUE
AB1EARTHENWARE, DELFTWARE ENG, FRAGMENT
37
AC1EARTHENWARE, DELFTWARE ENG, FRAGMENT, MISSING GLAZE
AD2DETACHED GLAZE, TIN ENAMELLED, FRAGMENT, PAINTED UNDER, BLUE
AE1COARSE EARTHEN, COLONO WARE, FRAGMENT
AF3CERAMIC, TOBACCO PIPE, IMPORTED, STEM, 5/64 INCHES
AG1CERAMIC, TOBACCO PIPE, IMPORTED, STEM, 4/64 INCHES
AH1GLASS, CLRLESS LEAD, FRAGMENT, STEMMED GLASS, MOLDED STEM, STEM, ANGULAR KNOP WITH TEAR DROP
AI3GLASS, CLRLESS LEAD, FRAGMENT, TABLE GLASS
AJ1GLASS, COLORED GLASS, FRAGMENT, PHARMACEUTICAL, GREEN
AK14GLASS, FRAGMENT, WINDOW GLASS
AL13GLASS, FRAGMENT, WINE BOTTLE
AM5BONE, FAUNAL SPECIMEN
AN1COPPER ALLOY, UPHOLSTERY TACK
AO1IRON ALLOY, UNID HARDWARE
AP1IRON ALLOY, NAIL, LESS THAN 2 IN, WROUGHT/FORGED
AQ2IRON ALLOY, NAIL, 2 TO 4 IN, WROUGHT/FORGED
AR12IRON ALLOY, NAIL, FRAGMENT
Context No.: 01BB-00148 TPQ: NDA
AA1GLASS, FRAGMENT, WINE BOTTLE
AB2BONE, FAUNAL SPECIMEN
Context No.: 01BB-00149 TPQ: 1775
AA1EARTHENWARE, DELFTWARE ENG, FRAGMENT
AB1REFINED EARTHEN, PEARLWARE, FRAGMENT, PRINTED UNDER, BLUE
AC3GLASS, FRAGMENT, WINDOW GLASS
AD2GLASS, FRAGMENT, WINE BOTTLE
AE1BONE, FAUNAL SPECIMEN
Context No.: 01BB-00155 TPQ: 1670
AA1COARSE EARTHEN, N MIDLAND SLIP, FRAGMENT, COMBED/DOTTED
AB3GLASS, FRAGMENT, WINDOW GLASS
AC1GLASS, FRAGMENT, WINE BOTTLE
AD1BONE, FAUNAL SPECIMEN
AE1QUARTZ, DEBITAGE, SEC/THIN FLAKE
Context No.: 01BB-00157 TPQ: 1880
AA1EARTHENWARE, DELFTWARE ENG, FRAGMENT, PAINTED UNDER, BLUE
AB5EARTHENWARE, DELFTWARE ENG, FRAGMENT
AC2EARTHENWARE, DELFTWARE ENG, FRAGMENT, MISSING GLAZE
AD4DETACHED GLAZE, TIN ENAMELLED, FRAGMENT
AE2REFINED EARTHEN, CREAMWARE, FRAGMENT
AF2COARSE EARTHEN, N MIDLAND SLIP, FRAGMENT
AG1COARSE EARTHEN, RED-BOD SLIP, FRAGMENT, SLIP DECORATED, PHILADELPHIA-TYPE
AH1COARSE EARTHEN, YORKTOWN-TYPE, FRAGMENT
AI1COARSE EARTHEN, COLONO WARE, FRAGMENT
AJ1CERAMIC, FIRECLAY, FRAGMENT, CRUCIBLE
AK1STONEWARE, WH SALT-GLAZED, FRAGMENT
AL1PORCELAIN, CH PORCELAIN, FRAGMENT, PAINTED UNDER, BLUE
AM1PORCELAIN, CH PORCELAIN, FRAGMENT
AN1PORCELAIN, CH PORCELAIN, FRAGMENT, PAINTED UNDER, BLUE
AO1PORCELAIN, CH PORCELAIN, FRAGMENT, PAINTED OVER, GHOST IMAGE
38
AP2GLASS, CLRLESS LEAD, FRAGMENT, TABLE GLASS, BANDED, PITCHER
AQ2GLASS, CLRLESS LEAD, FRAGMENT, TABLE GLASS
AR10GLASS, CLRLESS LEAD, FRAGMENT
AS3GLASS, COLORED GLASS, FRAGMENT, PHARMACEUTICAL, EMPONTILLED, BASE
AT3GLASS, COLORED GLASS, FRAGMENT, CONTAINER, GREEN, CASE BOTTLE?
AU77GLASS, FRAGMENT, WINDOW GLASS
AV61GLASS, FRAGMENT, WINE BOTTLE
AW1CERAMIC, TOBACCO PIPE, IMPORTED, PRESS MOLDED, STEM, 5/64 INCHES
AX2CERAMIC, TOBACCO PIPE, IMPORTED, PRESS MOLDED, STEM, 4/64 INCHES
AY1CERAMIC, TOBACCO PIPE, IMPORTED, PRESS MOLDED, BOWL
AZ3BONE, FAUNAL SPECIMEN
BA1SHELL, SHELL, OYSTER
BB1CHARCOAL
BC1FLINT, DEBITAGE, ANG/BLOCKY FRAG
BD2MORTAR, MORTAR, SHELL
BE1STONE, STONE
BF1PLASTER, PLASTER, WHITE WASH?
BG2LEAD ALLOY, WINDOW LEAD
BH1COPPER ALLOY, RING
BI9IRON ALLOY, NAIL, LESS THAN 2 IN
BJ35IRON ALLOY, NAIL, FRAGMENT
BK1GLASS, MANG SOLARIZED, FRAGMENT, BOTTLE
Context No.: 01BB-00158 TPQ: NDA
AA1PORCELAIN, CH PORCELAIN, FRAGMENT, PAINTED UNDER, BLUE
AB4GLASS, FRAGMENT, WINE BOTTLE
AC1IRON ALLOY, NAIL, 2 TO 4 IN, WROUGHT/FORGED
AD1IRON ALLOY, NAIL, FRAGMENT
Context No.: 01BB-00160 TPQ: NDA
AA1GLASS, FRAGMENT, WINDOW GLASS
AB1IRON ALLOY, NAIL, FRAGMENT
Context No.: 01BB-00161 TPQ: NDA
AA1GLASS, FRAGMENT, WINE BOTTLE
Context No.: 01BB-00162 TPQ: 1850
0DETACHED GLAZE, TIN ENAMELLED, FRAGMENT
AA1EARTHENWARE, DELFTWARE ENG, FRAGMENT, PAINTED UNDER, POLYCHROME, ROOSTER/CHICKEN LEG; TILE?
AB2EARTHENWARE, DELFTWARE ENG, FRAGMENT, PAINTED UNDER, BLUE
AC6EARTHENWARE, DELFTWARE ENG, FRAGMENT
AD4EARTHENWARE, DELFTWARE ENG, FRAGMENT, MISSING GLAZE
AE3DETACHED GLAZE, TIN ENAMELLED, FRAGMENT
AF8REFINED EARTHEN, CREAMWARE, FRAGMENT
AG1REFINED EARTHEN, PEARLWARE, FRAGMENT, MOCHA/DENDRITIC, POLYCHROME
AH1REFINED EARTHEN, PEARLWARE, FRAGMENT, SHELL EDGE
AI2REFINED EARTHEN, PEARLWARE, FRAGMENT
AJ1REFINED EARTHEN, WEDGWOOD GREEN, FRAGMENT
AK3STONEWARE, AMER BROWN, FRAGMENT
AL5STONEWARE, WH SALT-GLAZED, FRAGMENT
39
AM1STONEWARE, FULHAM SW, FRAGMENT
AN2PORCELAIN, CH PORCELAIN, FRAGMENT, PAINTED UNDER, BLUE
AO1PORCELAIN, CH PORCELAIN, FRAGMENT
AP2PORCELAIN, ENG BONE CHINA, FRAGMENT
AQ1GLASS, COLORED GLASS, FRAGMENT, WHITE
AR2CERAMIC, TOBACCO PIPE, IMPORTED, PRESS MOLDED, STEM, 5/64 INCHES
AS3CERAMIC, TOBACCO PIPE, IMPORTED, PRESS MOLDED, STEM, 4/64 INCHES
AT1CERAMIC, TOBACCO PIPE, IMPORTED, PRESS MOLDED, BOWL
AU4GLASS, CLRLESS LEAD, FRAGMENT, TABLE GLASS
AV20GLASS, CLRLESS LEAD, FRAGMENT, CONTAINER
AW1GLASS, CLRLESS NON-LD, FRAGMENT, CONTAINER, COPPER WHL ENGR
AX7GLASS, CLRLESS NON-LD, FRAGMENT, CONTAINER
AY1GLASS, COLORED GLASS, FRAGMENT, CONTAINER, AQUA
AZ2GLASS, COLORED GLASS, FRAGMENT, PHARMACEUTICAL
BA1GLASS, COLORED GLASS, FRAGMENT, PERFUME BOTTLE, MOLD BLOWN, BLUE
BB1GLASS, COLORED GLASS, FRAGMENT, CONTAINER, MOLD BLOWN, BLUE
BC128GLASS, FRAGMENT, WINDOW GLASS
BD1GLASS, FRAGMENT, CASE BOTTLE
BE27GLASS, FRAGMENT, WINE BOTTLE
BF21BONE, FAUNAL SPECIMEN
BG1SHELL, SHELL, OYSTER
BH1SHELL, SHELL, CLAM
BI5CHARCOAL
BJ5COAL, COAL
BK5SLATE, SLATE
BL2QUARTZITE, DEBITAGE, ANG/BLOCKY FRAG
BM1QUARTZITE, DEBITAGE, FLAKE FRAG/SHAT
BN1STONE, DEBITAGE, FLAKE FRAG/SHAT
BO1QUARTZITE, DEBITAGE, SEC/THIN FLAKE
BP3QUARTZITE, DEBITAGE
BQ1QUARTZITE, DEBITAGE, BIFACIAL
BR1QUARTZITE, DEBITAGE
BS1MORTAR, MORTAR, LIME
BT4COPPER ALLOY, BUTTON, TWO PIECE
BU1LEAD ALLOY, UNID HARDWARE, ROLLED/SHEET
BV1IRON ALLOY, UNID HARDWARE
BW2BOG IRON
BX5IRON ALLOY, NAIL, 2 TO 4 IN, WROUGHT/FORGED
BY2IRON ALLOY, NAIL, LESS THAN 2 IN, WROUGHT/FORGED
BZ3IRON ALLOY, NAIL, 2 TO 4 IN, CUT
CA3IRON ALLOY, NAIL, LESS THAN 2 IN, CUT
CB1IRON ALLOY, NAIL, LESS THAN 2 IN, WIRE
CC1IRON ALLOY, SCREW, LESS THAN 2 IN
CD29IRON ALLOY, NAIL, FRAGMENT
Context No.: 01BB-00163 TPQ: 1864
AA3EARTHENWARE, DELFTWARE ENG, FRAGMENT
AB3EARTHENWARE, DELFTWARE ENG, FRAGMENT, MISSING GLAZE
AC1DETACHED GLAZE, TIN ENAMELLED, FRAGMENT
AD1EARTHENWARE, DELFTWARE ENG, FRAGMENT, PAINTED UNDER, BLUE
AE1REFINED EARTHEN, CREAMWARE, FRAGMENT, PAINTED UNDER, POLYCHROME
AF2REFINED EARTHEN, CREAMWARE, FRAGMENT
40
AG6STONEWARE, WH SALT-GLAZED, FRAGMENT
AH1PORCELAIN, CH PORCELAIN, FRAGMENT, PAINTED OVER, POLYCHROME
AI1PORCELAIN, CH PORCELAIN, FRAGMENT, GHOST MARKS
AJ8PORCELAIN, CH PORCELAIN, FRAGMENT, PAINTED UNDER, BLUE
AK1CERAMIC, TOBACCO PIPE, IMPORTED, PRESS MOLDED, BOWL, 4/64 INCHES
AL1GLASS, CLRLESS LEAD, FRAGMENT, TABLE GLASS
AM7GLASS, CLRLESS LEAD, FRAGMENT, CONTAINER
AN2GLASS, CLRLESS NON-LD, FRAGMENT, CONTAINER, LEIGHTON'S PATENT GLASS
AO4GLASS, CLRLESS NON-LD, FRAGMENT, CONTAINER
AP1GLASS, COLORED GLASS, FRAGMENT, CONTAINER, ENAMELLED, WHITE
AQ3GLASS, COLORED GLASS, FRAGMENT, CONTAINER, ENAMELLED, WHITE
AR2GLASS, FRAGMENT, WINE BOTTLE
AS1GLASS, COLORED GLASS, FRAGMENT, PHARMACEUTICAL, AQUA
AT53GLASS, FRAGMENT, WINDOW GLASS
AU2GLASS, COLORED GLASS, FRAGMENT, CONTAINER, AQUA
AV1BONE, FAUNAL SPECIMEN
AW1MORTAR, MORTAR
AX2IRON ALLOY, UNID HARDWARE
AY1IRON ALLOY, UNID HARDWARE
AZ3IRON ALLOY, NAIL, 2 TO 4 IN, WROUGHT/FORGED
BA13IRON ALLOY, 2 TO 4 IN, WROUGHT/FORGED
Context No.: 01BB-00164 TPQ: 1864
AA2EARTHENWARE, DELFTWARE ENG, FRAGMENT
AB1DETACHED GLAZE, TIN ENAMELLED, FRAGMENT
AC2REFINED EARTHEN, CREAMWARE, FRAGMENT, PAINTED UNDER, POLYCHROME
AD3REFINED EARTHEN, CREAMWARE
AE1COARSE EARTHEN, COLONO WARE, FRAGMENT
AF1STONEWARE, DRY-BODIED SW, FRAGMENT, RED
AG5STONEWARE, WH SALT-GLAZED, FRAGMENT
AH5PORCELAIN, CH PORCELAIN, FRAGMENT, PAINTED UNDER, BLUE
AI1CERAMIC, TOBACCO PIPE, IMPORTED, PRESS MOLDED, STEM, 5/64 INCHES
AJ1COARSE EARTHEN, IBERIAN WARE, FRAGMENT
AK1GLASS, CLRLESS LEAD, FRAGMENT, TABLE GLASS, COPPER WHL ENGR
AL2GLASS, CLRLESS LEAD, FRAGMENT, TABLE GLASS
AM4GLASS, CLRLESS LEAD, FRAGMENT, CONTAINER
AN2GLASS, CLRLESS NON-LD, FRAGMENT, CONTAINER
AO1GLASS, COLORED GLASS, FRAGMENT, PHARMACEUTICAL, GREEN
AP2GLASS, COLORED GLASS, FRAGMENT, CONTAINER, LEIGHTON'S PATENT GLASS
AQ1GLASS, COLORED GLASS, FRAGMENT, CONTAINER, AMBER
AR25GLASS, FRAGMENT, WINDOW GLASS
AS3GLASS, FRAGMENT, WINE BOTTLE
AT1QUARTZITE, DEBITAGE, PRIM/RED FLAKE
AU1LEAD ALLOY, PRINTERS TYPE
AV3IRON ALLOY, NAIL, 2 TO 4 IN, WROUGHT/FORGED
AW2IRON ALLOY, NAIL, LESS THAN 2 IN, WROUGHT/FORGED
AX1IRON ALLOY, NAIL, LESS THAN 2 IN, CUT
AY5IRON ALLOY, NAIL, FRAGMENT
41
Context No.: 01BB-00165 TPQ: 1864
AA1EARTHENWARE, DELFTWARE ENG, FRAGMENT, PAINTED UNDER, POLYCHROME
AB1EARTHENWARE, DELFTWARE ENG, FRAGMENT, YELLOW
AC3EARTHENWARE, DELFTWARE ENG, FRAGMENT
AD5EARTHENWARE, DELFTWARE ENG, FRAGMENT, MISSING GLAZE
AE1DETACHED GLAZE, TIN ENAMELLED, FRAGMENT
AF2REFINED EARTHEN, CREAMWARE, FRAGMENT
AG1REFINED EARTHEN, PEARLWARE, FRAGMENT, PAINTED UNDER, "HOUSE" DESIGN
AH4REFINED EARTHEN, PEARLWARE, FRAGMENT, PAINTED UNDER, BLUE
AI1REFINED EARTHEN, PEARLWARE, FRAGMENT, SHELL EDGE, PAINTED UNDER, BLUE
AJ3REFINED EARTHEN, PEARLWARE, FRAGMENT
AK1STONEWARE, WH SALT-GLAZED, FRAGMENT, CORDONED
AL1STONEWARE, WH SALT-GLAZED, FRAGMENT, DOT/DIAPER/BASK, PRESS MOLDED
AM1STONEWARE, WH SALT-GLAZED, FRAGMENT, BARLEYCORN, PRESS MOLDED
AN2STONEWARE, WH SALT-GLAZED, FRAGMENT
AO3STONEWARE, DRY-BODIED SW, FRAGMENT, RED
AP2STONEWARE, STAFFS BROWN, FRAGMENT, CORDONED
AQ7PORCELAIN, CH PORCELAIN, FRAGMENT, PAINTED UNDER, BLUE
AR2PORCELAIN, CH PORCELAIN, FRAGMENT, PAINTED OVER, PRESS MOLDED, POLYCHROME
AS2PORCELAIN, PORCELLANEOUS, FRAGMENT
AT1CERAMIC, TOBACCO PIPE, IMPORTED, PRESS MOLDED, STEM, 5/64 INCHES
AU1CERAMIC, TOBACCO PIPE, IMPORTED, PRESS MOLDED, STEM, 4/64 INCHES
AV2GLASS, CLRLESS LEAD, FRAGMENT, TABLE GLASS
AW13GLASS, CLRLESS NON-LD, FRAGMENT, CONTAINER
AX3GLASS, CLRLESS NON-LD, FRAGMENT, CONTAINER
AY3GLASS, CLRLESS NON-LD, FRAGMENT, CONTAINER, LEIGHTON'S PATENT GLASS
AZ3GLASS, COLORED GLASS, FRAGMENT, PHARMACEUTICAL, AQUA
BA1GLASS, COLORED GLASS, FRAGMENT, CONTAINER, AQUA
BB1GLASS, COLORED GLASS, FRAGMENT, CONTAINER, AMBER
BC36GLASS, FRAGMENT, WINDOW GLASS
BD2GLASS, FRAGMENT, CASE BOTTLE
BE18GLASS, FRAGMENT, WINE BOTTLE
BF11BONE, FAUNAL SPECIMEN
BG1QUARTZITE, DEBITAGE, FLAKE FRAG/SHAT
BH0CHERT, DEBITAGE
BI1STONE, MISC/UNMODIF ST
BJ1COPPER ALLOY, UPHOLSTERY TACK
BK1COPPER ALLOY, BUTTON
BL1IRON ALLOY, UNID HARDWARE
BM1IRON ALLOY, UNID HARDWARE
BN4IRON ALLOY, NAIL, 2 TO 4 IN, WROUGHT/FORGED
BO1IRON ALLOY, NAIL, LESS THAN 2 IN, WROUGHT/FORGED
BP51IRON ALLOY, NAIL, FRAGMENT
Context No.: 01BB-00166 TPQ: 1864
AA1EARTHENWARE, DELFTWARE ENG, FRAGMENT
AB1EARTHENWARE, DELFTWARE ENG, FRAGMENT, MISSING GLAZE
AC2DETACHED GLAZE, TIN ENAMELLED, FRAGMENT
AD5REFINED EARTHEN, CREAMWARE, FRAGMENT
42
AE1REFINED EARTHEN, PEARLWARE, FRAGMENT
AF2REFINED EARTHEN, PEARLWARE, FRAGMENT, PAINTED UNDER, BLUE
AG2REFINED EARTHEN, WHITEWARE, FRAGMENT
AH1STONEWARE, NOTTINGHAM SW, FRAGMENT, CORDONED
AI1STONEWARE, FULHAM SW, FRAGMENT, CORDONED
AJ2PORCELAIN, CH PORCELAIN, FRAGMENT, PAINTED UNDER, BLUE
AK1PORCELAIN, PORCELLANEOUS, FRAGMENT
AL1CERAMIC, TOBACCO PIPE, IMPORTED, PRESS MOLDED, STEM, 4/64 INCHES
AM1GLASS, CLRLESS LEAD, FRAGMENT, TABLE GLASS
AN6GLASS, CLRLESS LEAD, FRAGMENT, CONTAINER
AO1GLASS, CLRLESS NON-LD, FRAGMENT, TABLE GLASS
AP6GLASS, CLRLESS NON-LD, FRAGMENT, CONTAINER, LEIGHTON'S PATENT GLASS
AQ10GLASS, CLRLESS NON-LD, FRAGMENT, CONTAINER
AR1GLASS, COLORED GLASS, FRAGMENT, CONTAINER, AQUA
AS1GLASS, COLORED GLASS, FRAGMENT, CONTAINER, GREEN
AT2GLASS, COLORED GLASS, FRAGMENT, CONTAINER, AMBER
AU42GLASS, FRAGMENT, WINDOW GLASS
AV3GLASS, FRAGMENT, WINE BOTTLE
AW5BONE, FAUNAL SPECIMEN
AX1SHELL, SHELL, CLAM
AY20SHELL, SHELL
AZ2QUARTZ, DEBITAGE, FLAKE FRAG/SHAT
BA1QUARTZ, DEBITAGE
BB2SLATE, SLATE
BC2COAL, COAL
BD4BOG IRON
BE1COPPER ALLOY, CLOTH FASTENER
BF2IRON ALLOY, NAIL, 2 TO 4 IN, WROUGHT/FORGED
BG4IRON ALLOY, NAIL, LESS THAN 2 IN, WROUGHT/FORGED
BH1IRON ALLOY, NAIL, LESS THAN 2 IN, CUT
BI1IRON ALLOY, NAIL, LESS THAN 2 IN, WIRE
BJ14IRON ALLOY, NAIL, FRAGMENT
Context No.: 01BB-00170 TPQ: 1762
AA1EARTHENWARE, DELFTWARE ENG, FRAGMENT
AB2EARTHENWARE, DELFTWARE ENG, FRAGMENT, MISSING GLAZE
AC6DETACHED GLAZE, TIN ENAMELLED, FRAGMENT
AD1REFINED EARTHEN, CREAMWARE, FRAGMENT
AE1COARSE EARTHEN, COLONO WARE, FRAGMENT
AF1STONEWARE, DRY-BODIED SW, FRAGMENT, RED
AG1PORCELAIN, CH PORCELAIN, FRAGMENT, PAINTED UNDER, BLUE
AH1PORCELAIN, CH PORCELAIN, FRAGMENT
AI1CERAMIC, TOBACCO PIPE, IMPORTED, PRESS MOLDED, BOWL
AJ1GLASS, CLRLESS LEAD, FRAGMENT, TABLE GLASS
AK1GLASS, CLRLESS LEAD, FRAGMENT, CONTAINER
AL1GLASS, CLRLESS NON-LD, FRAGMENT, TABLE GLASS, COPPER WHL ENGR
AM9GLASS, FRAGMENT, WINDOW GLASS
AN2GLASS, FRAGMENT, CASE BOTTLE
AO5GLASS, FRAGMENT, WINE BOTTLE
AP1IRON ALLOY, NAIL, LESS THAN 2 IN, WROUGHT/FORGED
AQ5IRON ALLOY, NAIL, FRAGMENT
Context No.: 01BB-00171 TPQ: 1762
AA3EARTHENWARE, DELFTWARE ENG, FRAGMENT
AB2EARTHENWARE, DELFTWARE ENG, FRAGMENT, MISSING GLAZE
43
AC4DETACHED GLAZE, TIN ENAMELLED, FRAGMENT
AD1REFINED EARTHEN, CREAMWARE, FRAGMENT, PAINTED UNDER, POLYCHROME
AE3STONEWARE, WH SALT-GLAZED, FRAGMENT
AF1PORCELAIN, CH PORCELAIN, FRAGMENT, PAINTED UNDER, BLUE
AG4GLASS, CLRLESS LEAD, FRAGMENT, TABLE GLASS
AH1GLASS, CLRLESS LEAD, FRAGMENT, CONTAINER
AI1GLASS, COLORED GLASS, FRAGMENT, CONTAINER, GREEN
AJ9GLASS, FRAGMENT, WINDOW GLASS
AK2GLASS, FRAGMENT, WINE BOTTLE
AL1IRON ALLOY, UNID HARDWARE
AM2IRON ALLOY, NAIL, LESS THAN 2 IN, WROUGHT/FORGED
AN6IRON ALLOY, NAIL, FRAGMENT
Context No.: 01BB-00172 TPQ: 1864
AA4EARTHENWARE, DELFTWARE ENG, FRAGMENT
AB7EARTHENWARE, DELFTWARE ENG, FRAGMENT, MISSING GLAZE
AC5DETACHED GLAZE, TIN ENAMELLED, FRAGMENT
AD1COARSE EARTHEN, COLONO WARE, FRAGMENT
AE3STONEWARE, WH SALT-GLAZED, FRAGMENT
AF2GLASS, CLRLESS LEAD, FRAGMENT, TABLE GLASS
AG3GLASS, CLRLESS LEAD, FRAGMENT
AH1GLASS, CLRLESS NON-LD, FRAGMENT, WINDOW GLASS, LEIGHTON'S PATNENT GLASS
AI9GLASS, FRAGMENT, WINDOW GLASS
AJ1IRON ALLOY, NAIL, 2 TO 4 IN, WROUGHT/FORGED
AK6IRON ALLOY, NAIL, FRAGMENT
AL1GLASS, FRAGMENT, WINE BOTTLE
Context No.: 01BB-00173 TPQ: 1762
AA1EARTHENWARE, DELFTWARE ENG, FRAGMENT, MISSING GLAZE
AB1REFINED EARTHEN, CREAMWARE, FRAGMENT, PAINTED UNDER, RED, GHOST IMAGE
AC1GLASS, FRAGMENT, WINDOW GLASS
AD1BONE, FAUNAL SPECIMEN
AE2SHELL, SHELL, SCALLOP
AF1COAL, COAL
AG2SLAG/CLINKER
AH1OTHER INORGANIC, FRAGMENT, BURNED
AI2OTHER INORGANIC, FRAGMENT, BURNED
Context No.: 01BB-00174 TPQ: NDA
AA1GLASS, FRAGMENT, WINDOW GLASS
AB1MORTAR, MORTAR, SHELL
Context No.: 01BB-00175 TPQ: NDA
AA3GLASS, FRAGMENT, WINDOW GLASS
AB1BONE, FAUNAL SPECIMEN
AC1IRON ALLOY, NAIL, LESS THAN 2 IN, WROUGHT/FORGED
Context No.: 01BB-00178 TPQ: 1915
AA4REFINED EARTHEN, CREAMWARE, FRAGMENT
AB1REFINED EARTHEN, CREAMWARE, FRAGMENT, PRINTED UNDER, BLACK
AC2REFINED EARTHEN, PEARLWARE, FRAGMENT
44
AD1REFINED EARTHEN, PEARLWARE, FRAGMENT, PRINTED UNDER, BLUE, MAKER'S MARK, "...RITISH..."
AE1REFINED EARTHEN, PEARLWARE, FRAGMENT, PRINTED UNDER, BLUE
AF1REFINED EARTHEN, WHITEWARE, FRAGMENT, ALKALINE GLAZE
AG1EARTHENWARE, FRAGMENT, BURNED
AH0COARSE EARTHEN, N DEVON, GRAV, FRAGMENT
AI4STONEWARE, DIPPED WSG, FRAGMENT
AJ1PORCELAIN, CH PORCELAIN, FRAGMENT, PAINTED UNDER, BLUE
AK1PORCELAIN, CH PORCELAIN, FRAGMENT
AL1CERAMIC, TOBACCO PIPE, IMPORTED, PRESS MOLDED, STEM, 4/64 INCHES
AM1GLASS, CLRLESS LEAD, FRAGMENT, CONTAINER
AN20GLASS, FRAGMENT, WINDOW GLASS
AO2GLASS, FRAGMENT, WINE BOTTLE
AP0GLASS, FRAGMENT, WINE BOTTLE
AQ2SHELL, SHELL, OYSTER
AR2SHELL, SHELL, CLAM
AS2MORTAR, MORTAR, SHELL
AT1BOG IRON
AU1COPPER ALLOY, WEIGHT
AV2IRON ALLOY, NAIL, OVER 4 IN, WROUGHT/FORGED
AW1IRON ALLOY, NAIL, LESS THAN 2 IN, WROUGHT/FORGED
AX3IRON ALLOY, NAIL, FRAGMENT
AY1PLASTIC, RING, PURPLE
Context No.: 01BB-00183 TPQ: 1775
AA4REFINED EARTHEN, CREAMWARE, FRAGMENT
AB2REFINED EARTHEN, PEARLWARE, FRAGMENT, PAINTED UNDER, BLUE
AC1PORCELAIN, CH PORCELAIN, FRAGMENT, PAINTED UNDER, BLUE
AD1GLASS, FRAGMENT, WINDOW GLASS
AE4BONE, FAUNAL SPECIMEN
AF1COAL, COAL
AG1SLAG/CLINKER
AH1IRON ALLOY, NAIL, 2 TO 4 IN, WROUGHT/FORGED
AI1IRON ALLOY, NAIL, FRAGMENT
Context No.: 01BB-00184 TPQ: 1845
AA1REFINED EARTHEN, WHITEWARE, FRAGMENT
AB1REFINED EARTHEN, IRONST/WH GRAN, FRAGMENT
AC1PORCELAIN, PORCELLANEOUS, FRAGMENT
AD2GLASS, FRAGMENT, WINDOW GLASS
AE4BONE, FAUNAL SPECIMEN
AF1IRON ALLOY, NAIL, 2 TO 4 IN, WROUGHT/FORGED
AG1IRON ALLOY, NAIL, LESS THAN 2 IN, WROUGHT/FORGED
AH1IRON ALLOY, NAIL, FRAGMENT
Context No.: 01BB-00188 TPQ: 1820
AA1REFINED EARTHEN, WHITEWARE, FRAGMENT
AB1STONEWARE, WH SALT-GLAZED, FRAGMENT
AC1PORCELAIN, CH PORCELAIN, FRAGMENT
AD3GLASS, FRAGMENT, WINDOW GLASS
AE1GLASS, FRAGMENT, WINE BOTTLE
AF42BONE, FAUNAL SPECIMEN
AG1MARL
AH7MORTAR, MORTAR, SHELL
AI2IRON ALLOY, NAIL, 2 TO 4 IN, WROUGHT/FORGED
AJ2IRON ALLOY, NAIL, FRAGMENT
45
Context No.: 01BB-00190 TPQ: 1820
0CERAMIC, TOBACCO PIPE, IMPORTED, PRESS MOLDED, BOWL
AA1PORCELAIN, PORCELLANEOUS, FRAGMENT
AB1CERAMIC, TOBACCO PIPE, IMPORTED, STEM, 5/64 INCHES
AC1CERAMIC, TOBACCO PIPE, IMPORTED, PRESS MOLDED, BOWL
AD2GLASS, FRAGMENT, WINE BOTTLE
AE4BONE, FAUNAL SPECIMEN
AF6MORTAR, MORTAR, SHELL
AG1OTHER INORGANIC, BURNED
AH2IRON ALLOY, NAIL, 2 TO 4 IN, WROUGHT/FORGED
AI1IRON ALLOY, NAIL, LESS THAN 2 IN, CUT, HAND HEAD
AJ6IRON ALLOY, NAIL, FRAGMENT
Context No.: 01BB-00192 TPQ: 1762
AA1REFINED EARTHEN, CREAMWARE, FRAGMENT
AB2STONEWARE, WH SALT-GLAZED, FRAGMENT
AC1PORCELAIN, CH PORCELAIN, FRAGMENT
AD1GLASS, CLRLESS LEAD, FRAGMENT, TABLE GLASS
AE2GLASS, FRAGMENT, WINDOW GLASS
AF5BONE, FAUNAL SPECIMEN
AG1MORTAR, MORTAR, SHELL
AH1IRON ALLOY, NAIL, 2 TO 4 IN, WROUGHT/FORGED
AI2IRON ALLOY, NAIL, FRAGMENT
Context No.: 01BB-00195 TPQ: NDA
AA1CERAMIC, TOBACCO PIPE, IMPORTED, PRESS MOLDED, STEM, 5/64 INCHES
AB1CERAMIC, TOBACCO PIPE, IMPORTED, PRESS MOLDED, STEM, 4/64 INCHES
AC1GLASS, FRAGMENT, WINDOW GLASS
AD2GLASS, FRAGMENT, WINE BOTTLE
AE7BONE, FAUNAL SPECIMEN
AF1BOG IRON
AG2IRON ALLOY, NAIL, 2 TO 4 IN, WROUGHT/FORGED
Context No.: 01BB-00196 TPQ: NDA
AA4GLASS, FRAGMENT, WINDOW GLASS
AB5BONE, FAUNAL SPECIMEN
AC1BOG IRON
AD1IRON ALLOY, NAIL, 2 TO 4 IN, WROUGHT/FORGED
AE1IRON ALLOY, NAIL, FRAGMENT
Context No.: 01BB-00199 TPQ: NDA
AA3GLASS, FRAGMENT, WINDOW GLASS
AB5GLASS, FRAGMENT, WINE BOTTLE
AC9BONE, FAUNAL SPECIMEN
AD1COAL, COAL
AE1IRON ALLOY, NAIL, LESS THAN 2 IN, WROUGHT/FORGED
Context No.: 01BB-00200 TPQ: NDA
AA1GLASS, FRAGMENT, WINE BOTTLE
Context No.: 01BB-00201 TPQ: NDA
AA1CERAMIC, FRAGMENT, DRAINAGE PIPE